Ungtae Kim

Dr. Ungtae Kim


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 September 2017 in Agriculture
Verified
Journal Article
Open access
PDF file
ADAmin Daghighi
Amin Daghighi
ANAli Nahvi
Ali Nahvi
UKUngtae Kim
Ungtae Kim
Because the available water resources of the Arjan plain region in Iran do not fully meet the watering requirements for plants in farmlands, the crops suffer from water stress, a situation that causes them to wilt. The aim of this study is to develop a water resources planning model that helps decision-makers determine an appropriate cultivation pattern, optimize the exploitation from surface water resources, and specify the method of allocating water across different farm crops to minimize the detrimental effects of water shortage. Through investigating various models of water resources planning and properties along with the governing conditions for each of these models, the linear programming model was selected as a suitable option due to its simplicity and practical applicability to water resource allocation planning. The model was run for a five-year period by considering gradual variations through the determination of the most appropriate exploitation pattern from the available water resources (surface and groundwater). Results reveal that the negative water balance can be improved gradually as positive, where it will reach +20 million m3 per year in 2040 from the current deficit of 236 million m3 with an 8% increased net profit.

28 August 2023 in Science of The Total Environment
Verified
Journal Article
Closed access
JCJeonghyeon Choi
Jeonghyeon Choi
UKUngtae Kim
Ungtae Kim
Sangdan KimSangdan Kim
Sangdan Kim

1 November 2015 in Journal of Contaminant Hydrology
Verified
Journal Article
Open access
JPJack C. Parker
Jack C. Parker
UKUngtae Kim
Ungtae Kim
The mono-continuum advection-dispersion equation (mADE) is commonly regarded as unsuitable for application to media that exhibit rapid breakthrough and extended tailing associated with diffusion between high and low permeability regions. This paper demonstrates that the mADE can be successfully used to model such conditions if certain issues are addressed. First, since hydrodynamic dispersion, unlike molecular diffusion, cannot occur upstream of the contaminant source, models must be formulated to prevent "back-dispersion." Second, large variations in aquifer permeability will result in differences between volume-weighted average concentration (resident concentration) and flow-weighted average concentration (flux concentration). Water samples taken from wells may be regarded as flux concentrations, while soil samples may be analyzed to determine resident concentrations. While the mADE is usually derived in terms of resident concentration, it is known that a mADE of the same mathematical form may be written in terms of flux concentration. However, when solving the latter, the mathematical transformation of a flux boundary condition applied to the resident mADE becomes a concentration type boundary condition for the flux mADE. Initial conditions must also be consistent with the form of the mADE that is to be solved. Thus, careful attention must be given to the type of concentration data that is available, whether resident or flux concentrations are to be simulated, and to boundary and initial conditions. We present 3-D analytical solutions for resident and flux concentrations, discuss methods of solving numerical models to obtain resident and flux concentrations, and compare results for hypothetical problems. We also present an upscaling method for computing "effective" dispersivities and other mADE model parameters in terms of physically meaningful parameters in a diffusion-limited mobile-immobile model. Application of the latter to previously published studies of systems that exhibit early breakthrough and extended tailing shows that the upscaled mADE model is able to describe the observed behavior with reasonable accuracy given only known physical parameters for the systems without any model calibration.

4 December 2010 in Water Resources Research
Verified
Journal Article
Open access
PDF file
JPJack Parker
Jack Parker
UKUngtae Kim
Ungtae Kim
MWMark Widdowson
Mark Widdowson
PKPeter Kitanidis
Peter Kitanidis
RGRandall Gentry
Randall Gentry
Simplified models have been proposed to describe dense nonaqueous phase liquids (DNAPL) source mass discharge versus time assuming that aqueous mass transfer is proportional to the DNAPL mass remaining raised to the power of a “source architecture” coefficient. Recent studies suggest that source discharge predictions may be improved using multiple functions for different architectures. However, multiple‐source functions require estimation of additional parameters, which can be difficult to do from available field data. A hypothetical problem was considered that involves a DNAPL source zone consisting of seven discrete trichloroethylene (TCE) sources within a roughly 120,000 m2 area, each having different release dates, masses, and rate parameters. A transport model was used to simulate dissolved TCE concentrations in 22 monitoring wells over a 23 year period. “Noise” representing conceptual model errors and sampling or measurement error was applied to produce synthetic monitoring data. Source mass and dissolution rates were computed for the total source and for various depth intervals for a 5 year period and were also overlaid with suitable “noise.” Data sets consisting of various subsets of the noisy monitoring and source data were employed to calibrate various model formulations. Results indicate that calibration using only near‐source discharge rates yield highly uncertain estimates of future mass discharge rates. Prediction accuracy is improved and uncertainty is reduced by calibrating to whole plume data in conjunction with source discharge estimates, especially if the latter are available for multiple depths. More complex models reduce prediction uncertainty up to a point beyond which added complexity was a liability unless additional or more accurate data are available.

1 December 2012 in Environmental Modelling & Software
Verified
Journal Article
Closed access
JPJack Parker
Jack Parker
UKUngtae Kim
Ungtae Kim
PKPeter Kitanidis
Peter Kitanidis
MCMike Cardiff
Mike Cardiff
XLXiaoyi Liu
Xiaoyi Liu
GBGreg Beyke
Greg Beyke

30 August 2017 in Water
Verified
Journal Article
Open access
PDF file
JRJoseph Rungee
Joseph Rungee
UKUngtae Kim
Ungtae Kim
Norris Reservoir is the oldest and largest reservoir maintained and operated by the Tennessee Valley Authority (TVA). Norris Dam received a new operating guide in 2004; however, this new guide did not consider projected climate change. In an aging infrastructure, the necessity to assess the potential impacts of climate change on water resources planning and management is increasing. This study used a combined monthly hydrologic model and a general circulation model’s (GCM) outcome to project inflows for three future time spans: 2030s, 2050s, and 2070s. The current operating guide was then assessed and optimized using penalty-function-driven genetic algorithms to gain insight for how the current guide will respond to climate change, and if it can be further optimized. The results showed that the current operating guide could sufficiently handle the increased projected runoff without major risk of dam failure or inundation, but the optimized operating guides decreased operational penalties ranging from 22 to 37 percent. These findings show that the framework used here provides water resources planning and management a methodology for assessing and optimizing current systems, and emphasizes the need to consider projected climate change as an assessment tool for reservoir operations.