Hao Zhang

Dr. Hao Zhang

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 September 2022 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
HFHongyu Fu
Hongyu Fu
QLQinghe Luo
Qinghe Luo
LBLingzhi Bao
Lingzhi Bao
BSBaigang Sun
Baigang Sun
QNQingyu Niu
Qingyu Niu
HZHao Zhang
Hao Zhang

1 April 2025 in Friction
Verified
Journal Article
Open access
PDF file
XWXinbo Wang
Xinbo Wang
LJLili Jin
Lili Jin
HZHao Zhang
Hao Zhang
RXRuifeng Xu
Ruifeng Xu
OSOleksandr Stelmakh
Oleksandr Stelmakh
YLYansong Liu
Yansong Liu
Hydrogen internal combustion engines are up-and-coming power devices in the current energy field. However, engine lubricants are prone to contact with hydrogen and water vapor during operation, and the impact of these gases on the tribological properties of the lubricants has not yet been clearly studied. In this work, the tribological performance and mechanism of emulsified lubricants with varying hydrogen content were investigated. The results demonstrated that the width and the depth of the wear track on the GCr15 steel blocks decreased by 86.8% and 80.4%, respectively, as the volume ratio of hydrogen gas to oil increased from 0% to 100%. The conversion of complete oxide layer (FeOOH-Fe2O3) and composite oxide layer (Fe-FeO-FeOOH-Fe2O3) at the frictional interface was proposed as the wear mechanism, and this mechanism was confirmed utilizing optical microscopy, contact 3D profilometry, scanning electron microscopy, and X-ray photoelectron spectroscopy (XPS). A complete oxide layer lubricated by pure oil results in severe adhesive wear at the friction interface, whereas a composite oxide layer under 80vol%-100vol% H2/oil emulsified lubricants was discovered to reduce oxidation corrosion and wear. The characteristics of this wear mechanism can be applied to reduce wear in tribo-pairs and lubricant designs of hydrogen internal combustion engines.

15 June 2024 in Engineering Failure Analysis
Verified
Journal Article
Closed access
PNPenghao Niu
Penghao Niu
HZHao Zhang
Hao Zhang
HFHongyu Fu
Hongyu Fu
OSOleksandr Stelmakh
Oleksandr Stelmakh
YLYifei Li
Yifei Li
JZJiaji Zhang
Jiaji Zhang

31 August 2024 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
YLYansong Liu
Yansong Liu
LJLili Jin
Lili Jin
HZHao Zhang
Hao Zhang
RXRuifeng Xu
Ruifeng Xu
XWXinbo Wang
Xinbo Wang
BSBaigang Sun
Baigang Sun

31 August 2024 in International Journal of Engine Research
Verified
Journal Article
Closed access
HFHongyu Fu
Hongyu Fu
HZHao Zhang
Hao Zhang
LZLimin Zhang
Limin Zhang
PNPenghao Niu
Penghao Niu
XLXukang Liu
Xukang Liu
OSOleksandr Stelmakh
Oleksandr Stelmakh
The commonly used spinning tin-bronze bushings assembled by interference sometimes fail causing the bushings to rotate or even come out from connecting rod small end. Previous studies have shown this failure to be related to the abnormal temperature of small end. Test samples with same material and process as the connecting rod small end were designed. The residual stress on inner surface and pressing force of bushings were tested before and after local heating. The results showed that the residual stresses on inner surface and maximum pressing force decrease with the increase of maximum temperature and thermal cycles when the temperature of bushing bottom reaches 160°C. A quarter model of connecting rod was applied to reveal the loosening mechanism. It is found that plastic deformation occurs around oil holes, resulting in variations in the stress field of bushing. It lessens the bonding force between bushing and connecting rod small end. Meanwhile, the residual stresses on inner surface decrease and then surface hardness of this area reduces, which makes it easier to adhere with piston pin and generate large friction. These results are crucial for the material and structure design of connecting rod small end bushings.

28 December 2023 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Closed access
HZHao Zhang
Hao Zhang
WZWendi Zhu
Wendi Zhu
YGYiqiao Guo
Yiqiao Guo
WDWei Du
Wei Du
XYXu Yang
Xu Yang
BMBingang Mei
Bingang Mei
During low-temperature starting, the high viscosity and poor fluidity of diesel engine lubricating oil make it difficult to be timely replenished to the friction pair, leading to the problems of starting difficulties and wear during cold starting. To address this issue, this study completed a simulation verification work through a bench test, and carried out a transient simulation of lubricating system oil filling in the range of 1–5 s starting time and −20°C to 80°C lubricating oil temperature to obtain the transient filling characteristics of the lubrication system oil path and the friction characteristics of the bearing. The results show that extending the starting time can effectively reduce the average dry sliding speed of the bearing, thereby reducing the frictional wear of the critical friction pairs during starting; when the oil temperature is between 20°C and 30°C, the average dry sliding speed of the bearing is low and the dry sliding distance is the shortest. The research results of this study are conducive to in-depth analysis of the lubrication oil filling mechanism during cold starting, and to determine a reasonable cold starting strategy from the perspective of lubrication.