Shadi M. Saadeh

Dr. Shadi M. Saadeh

National Center for Transportation, Green Technology, and Education (TransGET), California State University Long Beach, Long Beach, CA 90840, USA

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2013 in Road Materials and Pavement Design
Verified
Journal Article
Closed access
HHHamed Hakimelahi
Hamed Hakimelahi
SSShadi M. Saadeh
Shadi M. Saadeh
JHJohn Harvey
John Harvey
Fatigue cracking is a primary distress in asphalt concrete (AC) due to repetitive stresses and strains caused by both traffic loading and environmental factors. The fatigue resistance of AC is investigated by a number of fatigue tests. The main objective of this study is to investigate the use of the semi-circular bending (SCB) test as a quality assurance/quality control (QA/QC) measure for field construction. The comparison of fracture properties of seven AC mixtures from the SCB and beam fatigue test (BFT) is conducted. The J c and K 1c values for the seven mixtures were determined. The BFT was performed on the same mixtures and the initial stiffness, N f and plateau value (PV) were determined. The coefficient of variation (CV) ranged from 0% to 38% for J c and from 0% to 35% for K 1c. The CV ranged from 10% to 93% for the initial stiffness, 2% to 83% for N f and 8% to 167% for PV. The SCB J c and BFT N f and PV indicated lower fracture properties for PG64-10RAP (LIME), AN-HMA and WMA-ADVERA mixtures than other mixtures. The BFT N f and PV achieved similar ranking for all mixtures. There is good correlation between N f and PV with J c, and not a good correlation between the initial stiffness with J c, N f and PV. This has indicated that the initial stiffness is not a good representative for fracture properties of AC while J c, N f and PV are better indicators. The results of this study indicate that the SCB test has a great potential as a QA/QC test of fracture properties of asphalt mixtures.

1 September 2018 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
Wei CaoWei Cao
Wei Cao
LMLouay N Mohammad
Louay N Mohammad
MEMostafa Elseifi
Mostafa Elseifi
SCSamuel B. Cooper
Samuel B. Cooper
SSShadi M. Saadeh
Shadi M. Saadeh
The objective of this study is to correlate asphalt mixtures’ crack resistance with their in situ cracking performance. Ten mixtures were obtained from a full-scale experiment at the Federal Highway Administration (FHWA) Accelerated Loading Facility (ALF), which were constructed with various contents of reclaimed asphalt pavement (RAP) and recycled asphalt shingles (RAS), two warm-mix technologies, and two asphalt binder grades. The mixtures’ linear viscoelastic properties were assessed through dynamic modulus testing. Fracture resistance was characterized by the critical strain energy release rate (Jc ), which was obtained from semicircular bending (SCB) tests at intermediate temperature. The increase in RAP/RAS content was found to enhance mixture’s stiffness while reducing the mix crack resistance. No significant difference in terms of crack resistance was observed between the two used warm-mix technologies. The use of a soft binder was effective in improving the crack resistance of mixtures with a high RAP content. The generic fatigue model from the literature did not correlate well with the ALF test results; modification was achieved by introducing Jc as an indicator of crack resistance into the model form. The resulting Jc -based model exhibited an adequate correlation with field performance measured by the ALF test results.

14 December 2021 in Road Materials and Pavement Design
Verified
Journal Article
Closed access
SSShadi M. Saadeh
Shadi M. Saadeh
YAYazan Al-Zubi
Yazan Al-Zubi
PKPritam Katawal
Pritam Katawal
BZBasel Zaatarah
Basel Zaatarah
EFElham Fini
Elham Fini
Biogenic carbon made from biomass waste (referred to as Biochar here) has shown to enhance rheological and mechanical properties of asphalt binder. This paper presents the results of using biochar as an additive in Hot Mix Asphalt (HMA). The Semi-Circular Bend (SCB) test and the Hamburg Wheel Tracking (HWT) test were selected to analyze the resistance to fracture and rutting, respectively. Also, the resistance to colour degradation of HMA was evaluated using the Xenon Arc Test. The SCB test results suggested that biochar's presence led to an increase of strain energy and subsequently higher resistance to fracture. HWT test results showed that biochar's presence reduced total permanent deformation after 20,000 cycles and subsequently enhanced resistance to rutting. As for the resistance to colour degradation, biochar's addition helped preserve colour and decrease the surface degradation of the asphalt mixture exposed to solar radiation compared to the control mixture.

1 February 2024 in Journal of Cleaner Production
Verified
Journal Article
Closed access
SSShadi M. Saadeh
Shadi M. Saadeh
PKPritam Katawal
Pritam Katawal
SKSk Faisal Kabir
Sk Faisal Kabir
EFElham H. Fini
Elham H. Fini
HTHani Titi
Hani Titi

1 June 2018 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
SSShadi M. Saadeh
Shadi M. Saadeh
DRDavid Renteria
David Renteria
EMEnad Mahmoud
Enad Mahmoud
OEOmer Eljairi
Omer Eljairi
The semicircular bending (SCB) test has received significant attention as a fracture test for asphalt concrete (AC) mixtures. This study focuses on the variability of the SCB test, considering several factors, including mix gradation (Superpave and coarse matrix high binder), aggregate shape, air voids, aggregate type (granite, hard limestone, and soft limestone), and interface properties. The SCB test was modeled using a discrete element method approach to analyze the fracture behavior of the AC mixture. A total of 100 cases were produced for each mix combination, for which the interface property was set the same as that of the mastic. The effect of the interface was studied by generating 50 cases for each mix with some specific aggregate types. The generation of aggregates and air voids within the internal structure was done randomly. The simulation results suggested that the initiation of cracks and their propagation through the sample are related to the location of aggregate and air voids within the specimen. Furthermore, the aggregate-mastic contact bond increased the strength of the AC mixtures and reduced the coefficient of variation for several cases.

9 April 2019 in MATEC Web of Conferences
Verified
Journal Article
Open access
DRDavid Renteria
David Renteria
SSShadi M. Saadeh
Shadi M. Saadeh
EMEnad Mahmoud
Enad Mahmoud
The objective of this paper is to investigate the effect of air voids on the fracture properties of asphalt mixtures using SCB test in Discrete Element Method (DEM). Superpave and Coarse Matrix High Binder (CMHB) mixtures gradation were used to generate the percentages of aggregate, mastic, and air voids within the specimens. Aggregates and air voids were randomly generated for each asphalt mixture case. Model results illustrate that the crack initiation and propagation is controlled by the location of the aggregate particles and air voids in the mixture. Additionally, the absence of air voids above the tip of the notch increases the stiffness of the sample and increase its resistance to failure. The novelty of using DEM and the random generation technique for generating numerical specimens proved to be a useful approach in investigating the properties of the mastic, aggregate and interface as they relate to fracture of asphalt mixtures.