At present, the direct gold determination in geological samples by inductively coupled plasma mass spectrometry (ICP-MS) is still an arduous challenge due to both spectral and background interferences. It is very important and necessary to study the pretreatment processes; therefore, the polyurethane foam treatment and sample digestion methods are explored and compared here. The experimental results showed that the gold adsorption rate of treated foam was significantly improved as the impurities in the foam were cleaned up, and the potential difference of the liquid membrane was increased. Meanwhile, the combination of the foam enrichment and thiourea desorption achieved the selective adsorption and desorption of gold ions, eliminated the interference of coexisting ions, and perfected the detection limits. Compared with the traditional electric heating plate digestion method, microwave digestion, a closed digestion method, had the advantages of less sample and reagent dosage, short time consumption, high degree of automation, thorough digestion, good security, and environmental friendliness and met the requirements of green chemistry development. The proposed microwave digestion-foam enrichment-thiourea desorption-ICP-MS determination method was applied to the gold test in soil samples of the actual gold mining area. It has the great potential as a routine laboratory procedure.

The rational utilization of solid waste has always been a worldwide concern. In this study, coal fly ash (CFA) and red mud (RM) were used in combination to synthesize efficient heavy metal adsorbents. A new way of resource recycling was provided with the collaborative reuse of CFA and RM. To obtain the modified composite materials, CFA and RM were mixed and melted in three ratios. After modification, these materials were then utilized to adsorb Pb, Cu, and Cd in water in both single and ternary systems. The physicochemical properties of CFA, RM, and three modified composite materials were measured by X-ray diffraction analysis, energy dispersive X-ray spectroscopy, scanning electron microscope, Fourier transform infrared spectroscopy, vibrating sample magnetometer, surface area analyzer, and porosity analyzer. In the single and ternary systems, the effects of the modified composite material dosage, solution pH, initial concentration of heavy metals, and adsorption time were discussed, and the results were better fitted with the Langmuir isotherm and the pseudo-second-order kinetic. It was discovered that the modified composite materials had a greater specific surface area (63.83 m²/g) than CFA and RM alone, as well as superior adsorption capacity and magnetic characteristics. The adsorption capacities of C1R4 for Pb, Cu, and Cd were 149.81 mg/g, 135.96 mg/g, and 127.82 mg/g in the single system, while those of Cu and Cd decreased slightly in the ternary system, and the preferential adsorption order of the modified composite materials for heavy metal ions was Pb > Cu > Cd. Among the three modified composite materials, C1R4 had the best adsorption capacity.

The huge annual output of coal fly ash is harmful to the environment, but it is widely used because of its good adsorption potential. In this study, using coal fly ash as a raw material and sodium hydroxide as an activator, a novel adsorbent was synthesized at 300 °C and used to adsorb low concentrations of ammonia nitrogen from water. In this study, scanning electron microscopy, X-ray diffraction analysis, Fourier transform infrared spectroscopy, energy dispersive X-ray spectroscopy, and a surface area and porosity analyzer were used to analyze the adsorbent’s physicochemical properties. The results showed that after alkali modification, the activity of the adsorbent had greatly enhanced. The impacts of solution pH, adsorbent dosage, adsorption time, and initial concentration of ammonia nitrogen on the adsorption capacity and removal efficiency were evaluated through a series of adsorption experiments. Moreover, the adsorption data were better fitted to the pseudo-second-order kinetic model and Langmuir model, indicating that the adsorption process was mainly chemical adsorption and monolayer uniform adsorption. As a result, the new adsorbent is inexpensive and effective, and it could be used to remove low-concentration ammonia nitrogen from water with a maximum removal efficiency of approximately 89%.

This study collected 1135 topsoil samples of cultivated land in Laiyang County, eastern China, to analyze the distribution, pollution and health risks of heavy metals (As, Cd, Cu, Cr, Hg, Ni, Pb and Zn). The results show that: (1) the levels of eight heavy metals at some sites were higher than the risk screening values in China, and there was heavy metal pollution. (2) An improved geoaccumulation index was used to evaluate soil pollution. The average value of I_geo before and after improvement was 0.32 (I_ml, no pollution to medium pollution) and −0.04 (I_ol, no pollution), respectively. (3) Hg and Cd were identified as the main contributors to ecological risk in this study, with a cumulative ecological risk contribution percentage > 65%. The results of the potential ecological risk index (PERI) show that 9.3% of the sampling sites were considered to have moderate ecological risk. (4) As, Pb, Ni and Cu made a contribution of >95% in terms of non-carcinogenic risk to adults and children through different exposure routes, and different soil intake routes posed no non-carcinogenic risk to adults; there was a sampling site with HQ_Children > 1, which was consistent with the non-carcinogenic risk site, indicating that children in this location and surrounding areas are more likely to face dual health risks. Therefore, it is necessary to promote the risk management of heavy metals in the study area in order to safely use soil resources.