Corn starch was plasticized by glycerol suspension in a twin-screw extruder, in which the glycerol suspension was the pre-dispersion mixture of glycerol with nano-SiO2. Polylactide (PLA)/thermoplastic starch/SiO2 composites were obtained through melt-blending of PLA with thermoplastic starch/SiO2 in a twin-screw extruder. The nonisothermal crystallization behavior of PLA in the composites was investigated by differential scanning calorimetry. An interface of PLA with thermoplastic starch was proven to exist in the composites, and its interfacial bonding characteristics were analyzed. The interfacial binding energy stemming from PLA with thermoplastic starch exerts a significant influence on the segmental mobility of PLA at the interface. The segmental mobility of PLA is gradually improved by increasing interfacial binding energy, and consequently, the relative crystallinity on the interface exhibits progressive promotion. The Jeziorny model could well describe the primary crystallization of PLA in the composites. The extracted Avrami exponents based on the Jeziorny model indicate that the primary crystallization of PLA follows heterogeneous nucleation and three-dimensional growth. This study has revealed the intrinsic effect of the interfacial segmental mobility on the nonisothermal crystallization behavior of PLA in composites, which is of technological significance for its blow molding.
Silicone rubber (SR)/vinyl-graphene oxide (vinyl-GO) nanocomposites were prepared through the hydrosilylation reaction of silicon hydrogen polydimethylsiloxane (H-PDMS) with vinyl polydimethylsiloxane (vinyl-PDMS), in which vinyl-GO was used as a nano filler. The thermally conductive and antistatic properties of the nanocomposites, and their tensile strength and thermal stability were evaluated. The thermally conductive and antistatic properties increased naturally when the nanocomposites had eight to nine parts of vinyl-GO. The addition of 9 parts of vinyl-GO increased the thermal conductivity to 0.44 from 0.17 W/m−1·K−1 of neat SR and the surface resistance value to 108 from 1014 Ω of neat SR. Vinyl-GO is effective in improving the tensile strength and toughness of the nanocomposites. The tensile strength and elongation at break of the nanocomposites were much higher than that of neat SR, especially for 10 parts of vinyl-GO in the nanocomposite, and the tensile strength was 1.84 MPa and the elongation at break was 314.1%. Additionally, compared with neat SR, the nanocomposites had a much higher thermal stability. For eight parts of vinyl-GO in the nanocomposites, H-PDMS with the selected silicon hydrogen content and vinyl-PDMS with the selected vinyl content could offer an appropriate cross-linking degree that suits the character of GO. When the nanocomposite had eight parts of vinyl-GO, its scanning electron microscope exhibited a monolayer GO with folded, twisted, and local surface folds. However, there was a certain amount of multilayer aggregation of GO for 10 parts of vinyl-GO in the nanocomposite.
1 January 2013 in Separation Science and Technology
A new synthesis method of aromatic diamine, 4-aminobenzoylpiperazine (4-ABP), was studied from 4-aminobenzoic acid and 1-formyl piperazine for the preparation of nanofiltration membrane. The structure of 4-ABP was identified by FT-IR spectra and 1H NMR spectra. The resulting 4-ABP was used as aqueous monomer to fabricate a thin film on porous polyethersulfone (PES) ultra filtration membranes by interfacial polymerization (IP) with trimesoyl chloride (TMC) as organic monomer. The salt rejection order of these thin film composite (TFC) nanofiltration(NF) membranes is Na2SO4>MgSO4>MgCl2>NaCl. This sequence indicated that the membranes were negatively charged.
13 January 2022 in Journal of Vinyl and Additive Technology