This research aims to investigate the bearing capability of deep helical anchors and grouped helical anchors under uplift or lateral loads using field experiments. Grouped helical anchors may serve as a viable alternative to traditional deep foundations, offering increased resistance against uplift and lateral forces. The study of group effect primarily focuses on vertically installed helical anchors, with few data available on various configurations of grouped helical anchors. This research includes a total of 12 single-helix anchors, 4 double-helix anchors, and 4 grouped helical anchors, with anchor plate diameters of 400 mm and maximum embedment depths of 7.4 m. There are two configurations of grouped helical anchors, each with different platforms. This article studies the effect of some factors, including the embedment depth, the number of anchor plates, the spacing between anchor shafts, the selection of failure criteria, and the group effect. The primary findings indicate that adding the anchor plates to single-helix anchors without extending the shaft length does not increase uplift or lateral capacity. In this soil condition, the group efficiency of double-helix anchors is higher than 1. By comparing the group efficiency and economy of the G1 and G2 grouped helical anchors, it is highly recommended to use the G2 configuration. The data obtained from this work may also serve as a valuable tool for validating numerical models used to analyze interactions among grouped helical anchors.

Helical anchors have been widely used in geotechnical engineering due to their large uplift resistance. However, the current knowledge of the cyclic performance of helical anchors is still insufficient. Consequently, a series of small-scale model tests are carried out in sand to investigate the influences of embedment ratio, sand compactness and the cyclic parameters on the monotonic, cyclic and post-cyclic performance of single-helix anchors. The tests results indicate that the single-helix anchors with optimal embedment ratio still exhibit a relatively high uplift capacity after suffering cyclic load. The cyclic frequency has the greatest influence on the accumulated displacement, and the influence of amplitude is relatively greater than that of the mean cyclic load. The anchors in dense sand exhibit better performance to resist pullout than those in medium–dense sand under the same cyclic parameter ratios. Moreover, the correlation of post-cyclic uplift capacity and displacement after cyclic loading as well as the possible influence of the upward displacement on the sand flow above the helix are discussed.

The uplift capacity of helical anchors is generally taken as the control condition for design in different applications, including transmission tower foundations and offshore structures. However, it is difficult to identify the failure surface for a deep helical anchor, which may result in an incorrect assessment of uplift capability. This research proposes a new unified method to estimate the uplift capacity of deep single-helix and multi-helix anchors based on the investigation of failure mechanisms. The deep failure mode was identified by FEM analysis using a modified Mohr–Coulomb model considering the strain softening of sand, along with the coupled Eulerian–Lagrangian technique. Thereby, a simplified rupture surface is proposed, and the equations estimating the uplift capacity are presented by the limit equilibrium method. Two important factors—the lateral earth pressure coefficient and the average internal friction angle included in the equations—are discussed and determined. The comparisons with centrifugal tests verify the reasonability of the proposed method.

There is often obvious particle breakage for silica sand under high-stress, which will lead to the bearing capacity reduction and excessive settlement of the foundation. This paper focuses on the particle breakage characteristics of marine silica sand from the East China Sea under high-stress conditions. A series of conventional triaxial tests for silica sand, including consolidated drained (CD) and consolidated undrained (CU) shear tests, were conducted under the confining pressures in the range of 2–8 MPa to investigate the breakage rule during the shearing process. The developments of particle breakage index B_r with axial strain ε₁ and volumetric strain ε_v present hyperbolic and linear trends, respectively. A hyperbolic model was adopted to describe the relationship of B_r and ε₁ and the corresponding model parameters were obtained. The particle breakage index also has a good correlation with the input work per unit volume under various average stresses, regardless of the stress history. Furthermore, the relationship between the fractal dimension and the particle breakage was studied based on the particle size distribution curve. It is concluded that the fractal dimension increases in an up–convex hyperbolic trend with the increase of particle breakage index. The dividing radius for whether the silica sand particles exhibit the fractal features is determined as approximately 0.4 mm. This is anticipated to provide reference and supplementary test data for analyzing sand constitutive models/environments regarding particle crushing.

Helical anchors have been extensively employed as foundation systems for carrying tension loads due to their installation efficiency and large uplift capacity. However, the installation influences of helical anchors are still not well understood, especially for multi-helical anchors. The matrix discrete element method was used to model the process of helical anchor penetration and pull-out in dense sand to investigate the effects of the anchor geometry and advancement ratio (AR, the relative vertical movement per rotation) on soil disturbance, the particle flow mechanism, and the uplift capacity. For shallow helical anchors, the overall disturbance zone is the shape of an inverted cone after installation, while for deep helical anchors, it is funnel-shaped. The advancement ratio has significant effects on the soil particle movement and uplift capacity of helical anchors. The soil particle flow mechanism around helical plates has been identified for single-helix anchors at various advancement ratios, and for double-helix anchors, the influence of the top plate on particle movement during installation was investigated. The uplift capacities of both single- and double-helix anchors increase with the decrease in the AR (AR = 0.5~1), and the influence decreases with the anchor embedment ratio. The efficiency of double-helix anchors induced by installation is close to 1 at pitch-matched installation (AR = 1), indicating that the impact of the top plate during installation is minimal in this case.