Dongsik Kim

Prof. Dongsik Kim

Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Korea

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 May 2006 in Journal of Heat Transfer
Verified
Journal Article
Closed access
PDF file
SKSang Hyun Kim
Sang Hyun Kim
SCSun Rock Choi
Sun Rock Choi
Dongsik KimDongsik Kim
Dongsik Kim

12 May 2006 in International Journal of Thermophysics
Verified
Journal Article
Closed access
PDF file
SCSun Rock Choi
Sun Rock Choi
Dongsik KimDongsik Kim
Dongsik Kim
SCSung-Hoon Choa
Sung-Hoon Choa
SLSung-Hoon Lee
Sung-Hoon Lee
JKJong-Kuk Kim
Jong-Kuk Kim

1 August 2007 in Review of Scientific Instruments
Verified
Journal Article
Closed access
PDF file
SCSun Rock Choi
Sun Rock Choi
JKJoonwon Kim
Joonwon Kim
Dongsik KimDongsik Kim
Dongsik Kim
This work presents a method to measure the thermal conductivity and heat capacity of electrically conducting small-volume liquid samples using the 3ω technique. A mathematical model of heat transfer is derived to determine the thermal properties from the 3ω signal considering the device geometry. In order to validate the model, an experimental apparatus has been designed and set up to measure the thermal properties (thermal conductivity and heat capacity) of seven different liquid samples. The results show good agreement with other literature values, demonstrating that the suggested method is effective for measuring the thermal properties of electrically conducting liquids. More importantly, the result with a sample volume of 1μl demonstrates the resolution of the thermal conductivity as precise as 0.01% which corresponds to a thermal-conductivity change of 10−4W∕mK in the case of water-based solutions.

8 February 2005 in Journal of Applied Physics
Verified
Journal Article
Closed access
HLHyunkyu Lim
Hyunkyu Lim
DJDeoksuk Jang
Deoksuk Jang
Dongsik KimDongsik Kim
Dongsik Kim
JLJin Won Lee
Jin Won Lee
JLJong-Myoung Lee
Jong-Myoung Lee
It has been shown that the laser shock cleaning (LSC) method is effective for eliminating micron- and submicron-scale particulates from solid surfaces. In the LSC process, a high-power laser pulse induces optical breakdown of the ambient gas close to the solid surface to be cleaned and the subsequently-created shock wave followed by a high-speed flow stream detaches the particles. Therefore, there should be a strong correlation between the dynamics of the shock wave and the cleaning performance. In this work, experimental analyses are conducted to measure the cleaning performance using micron-sized alumina particles attached to a silicon surface. The experimental data showing the particle-removal performance are compared with the results of the dynamics of the laser-induced shock waves, leading to a simple model for particle removal by the LSC scheme in the continuum-flow regime.

27 March 2019 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
WJWonjong Jeong
Wonjong Jeong
YKYoung-Sam Kwon
Young-Sam Kwon
Dongsik KimDongsik Kim
Dongsik Kim
Although three-dimensional (3D) printing of tungsten parts by Powder Bed Fusion (PBF) has been demonstrated by multiple research groups, a directed energy deposition (DED) process for fabricating pure tungsten structures has never been reported. This work reports successful fabrication of pure tungsten structures by DED, revealing the required process conditions. The effect of laser power, scan speed, powder feed rate and carrier gas velocity on the stability and properties of the structures is first analyzed, based on which the proper process condition for effective 3D printing of tungsten parts is proposed. Fabrication of a rectangular tube of 110 mm in height is demonstrated using an in-house DED printing system. Analyses of the fabricated samples show that the density and the hardness can be as high as 18.9 g/cm3 (98.4% of the theoretical value) and 3.9 GPa, respectively. The results indicate that the optimal condition for 3D printing of tungsten is 400 ~ 530 J/mm2 in terms of specific energy and that high-speed or high-mass injection of powder can induce waviness on the surface. This work suggests that DED can be a promising alternative to produce pure tungsten parts in various applications.

5 September 2016 in RSC Advances
Verified
Journal Article
Open access
PDF file
JHJeonghong Ha
Jeonghong Ha
BLBong Jae Lee
Bong Jae Lee
DHDavid J. Hwang
David J. Hwang
Dongsik KimDongsik Kim
Dongsik Kim
This work reports a method for nanowelding silver nanowires (AgNWs) using ultrashort laser pulses to minimize thermal damage on flexible substrates. Because of localized field enhancement and limited thermal diffusion, femtosecond laser irradiation enabled joining of AgNWs only at junctions, maintaining their original crystalline structure. The femtosecond laser nanowelding process produced neither breakup of the nanowire (NW) junction nor thermal aggregation. In addition, the sheet resistance and transmittance of the AgNW network were improved up to 25 Ω sq−1 and over 94% at 550 nm, respectively. The femtosecond laser irradiation caused considerably less damage to a polymer substrate than nanosecond laser irradiation. The proposed nanowelding process is expected to serve as a useful tool to fabricate integrated plasmonic devices as well as transparent conducting electrodes on flexible substrates.