Vladimir Il’yashchenko

Vladimir Il’yashchenko


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
ASAlexander Vladimirovich Shevlyagin
Alexander Vladimirovich Shevlyagin
VIVladimir Il’yashchenko
Vladimir Il’yashchenko
Aleksandr KuchmizhakAleksandr Kuchmizhak
Aleksandr Kuchmizhak
EMEugeny Mitsai
Eugeny Mitsai
AAAndrey V. Amosov
Andrey V. Amosov
Sergei KulinichSergei Kulinich
Sergei Kulinich
This paper reports on a facile bottom-up method for the direct integration of a silicon (Si)-magnesium silicide (Mg2Si) heterojunction solar cell (HSC) with a textured rear reflector made of stainless steel (SS). Modified wet chemical etching and post processing of SS substrates resulted in the formation of both a rough surface texture and diffusion barrier layer, consisting of magnetite (Fe3O4) with reduced optical reflection. Then, Si, Mg2Si and CaSi2 layers were stepwise thermally evaporated onto the textured SS surface. No traces of Fe and Cr silicide phases were detected by Raman spectroscopy, confirming effective suppression of impurity diffusion from the SS to the upper layers at least at temperatures required for Si deposition, as well as Mg2Si and CaSi2 formation. The obtained black-SS/Fe3O4/Si/Mg2Si/CaSi2 sample preserved, to some extent, its underlying textured morphology and demonstrated an averaged reflection of 15% over the spectral range of 200–1800 nm, while its prototype HSC possessed a wideband photoresponse with a photoelectric conversion efficiency of 7.5% under AM1.5 illumination. Moreover, Si layers deposited alone onto a black-SS substrate demonstrated competitive antireflection properties compared with black Si (b-Si) obtained by traditional top-down etching approaches, and hybrid b-Si/textured-SS structures with a glue-bonded interlayer.

13 October 2009 in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
Verified
Journal Article
Closed access
PDF file
Nikolai Inokentevich PlyusninNikolai Inokentevich Plyusnin
Nikolai Inokentevich Plyusnin
VIVladimir Il’yashchenko
Vladimir Il’yashchenko
SKS. A. Kitan’
S. A. Kitan’
SKSlava Krylov
Slava Krylov
This paper is devoted to the study of the morphology, growth, electronic structure, and stability of ultrathin (0.03–3 nm) Co and Fe films on the Si(111) and Si(100) surfaces using Auger-electron spectroscopy, electron-energy loss spectrometry, low-energy electron diffraction, and atomic-force microscopy. It is shown that layer-by-layer growth of the metal with the formation of the film nanophase and the segregation of a submonolayer amount of Si on the film’s nanophase surface occurs during the process of layer-by layer growth of Co and Fe on Si(111)-7 × 7 and Si(100)-2 × 1 at room temperature after the growth of two-dimensional metal phases (the surface phase, the monolayer, and two metal monolayers). After these stages, the formation and growth of the bulk’s metal phase with the dissolution of silicon segregated before occur. It is shown that the upper layers of Si adjoining the surface phase, the monolayer, and two Co and Fe monolayers have respectively three different densities of the electron plasma that are higher than the density of the electron plasma in the volume of the silicon substrate. The nonmonotonous character of the morphological and chemical stability of Fe films with quantum-size thicknesses on Si(100) is discovered. After annealing, the film is first smooth, then it is nonuniform across its thickness; afterwards it is again smooth and then nonuniform across its thickness. In this case, the metal phase, different Fe silicides, and the bulk’s metal phase form successively in Fe films on Si(100) after annealing.