One of the main tasks of road managers is to plan maintenance interventions, which is currently in practice often done using a simple ranking-based method. However, an increasing number of researchers are focusing their efforts on supporting the planning process using operations research models. Models that have been developed can optimally group maintenance interventions: (1) in a single work zone, taking into consideration both work zone and asset related costs, and (2) in multiple work zones, taking into consideration only asset-related costs. In this paper, a new operation research model is developed to optimally group maintenance interventions in multiple work zones, taking into consideration both work zone and asset-related costs. The new model is used to optimally group maintenance interventions for a road network located in Fujian province in China. The improvement obtained from using the new model is compared to the result determined using an operation research model that can only determine one optimal group of intervention at a time, and one determined using a commonly used ranking-based method. It is shown that the new model results in the highest net-benefit, and that both operation research models result in higher net benefits than the ranking-based method.
Traffic conflict technology (TCT) is widely used to assess the safety of work zones. The current TCT is temporal and (or) spatial proximity defined based, which can only detect two-vehicle or multi-vehicle conflicts, and is not competent for single-vehicle conflicts. However, single-vehicle accidents in work zones are also severe. This study proposes a detection method for all types of traffic conflicts in work zones. Based on vehicle micro-behavior data, evasive behavior is detected by automatic segmentation, Support Vector Machine (SVM)-based behavior identification, and threshold-based judgment methods. Two-vehicle or multi-vehicle conflicts are detected by classical proximity defined-based method, i.e., the surrogate safety assessment model (SSAM). By comparing the analysis results of the evasive behavior with the one of SSAM, single-vehicle conflicts can be detected. Taking a practical work zone as an example, the effectiveness of this method in detecting all types of traffic conflicts in work zones is verified. The single-vehicle conflict can be subdivided into 10 types according to basic behavior types, such as straight-line driving and decelerating. The two or multi-vehicle conflicts can be subdivided into three types, such as rear-end conflict. The example also verifies the applicability of this method under different traffic volume scenarios.
10 January 2024 in Journal of Advanced Transportation
The number of road maintenance operations in China is increasing. Work zones can interfere with everyday driving and bring significant safety hazards to the throughput vehicles and construction personnel. However, there is currently a lack of effective methods to conduct a dynamic risk assessment of work zones and provide control guidance when necessary. Therefore, this study proposes a dynamic risk assessment and control framework for the work zones. The framework adopts a closed‐loop control and dynamic monitoring architecture. A massive amount of microscopic data on vehicles’ behavior is obtained based on advanced data collection technologies (including multicamera multiobject tracking, naturalistic driving, and microscopic traffic simulation). Traffic conflicts between single vehicle and two‐ or multivehicle are detected using vehicle behavior analyzing technology and the surrogate safety assessment model. A comprehensive assessment index, i.e., UTECN (unit total equivalent conflict number), is established that can consider the severity and possibility of accidents caused by conflicts based on the vehicle collision energy theory, probability theory, and risk management theory. A risk assessment standard is established based on the level of safety service. The framework is first implemented in a simulation environment, and its feasibility and effectiveness are verified by taking a work zone of Shanghai Waihuan Expressway S20 as a case study. The result shows that the framework has good practicality. Under a moderate traffic level, the risk of the work zone can be assessed within 20 minutes. It can be quickly and effectively controlled at an acceptable level after several iterations, which is of great significance for ensuring the safety of life and property of throughput vehicles and construction personnel within the work zone.
5 September 2024 in Journal of Infrastructure, Policy and Development
Given the large amount of railway maintenance work in China, whereas the maintenance time window is continuously compressed, this paper proposes a novel network model-based maintenance planning and optimization method, transforming maintenance planning and optimization into an integer linear programming problem. Based on the dynamic inspection data of track geometry, the evaluation index of maintenance benefit and the model of the decay and recovery of the track geometry are constructed. The optimization objective is to maximize the railway network’s overall performance index, considering budget constraint, maximum length constraint, maximum number of maintenance activities within one single period constraint, and continuity constraint. Using this method, the track units are divided into several maintenance activities at one time. The combination of surrounding track units can be considered for each maintenance activity, and the specific location, measure, time, cost, and benefit can be determined. Finally, a 100 km high-speed railway network case study is conducted to verify the model’s effectiveness in complex optimization scenarios. The results show that this method can output an objective maintenance plan; the combination of unit track sections can be considered to expand the scope of maintenance, share the maintenance cost and improve efficiency; the spatial-temporal integrated maintenance planning and optimization can be achieved to obtain the optimal global solution.
Optimizing the maintenance operation start time can greatly reduce the delays caused by the maintenance operations. A real-time traffic status data acquisition method based on real-time traffic map was first proposed, and then a method that can convert real-time traffic status into real-time traffic volume was put forward. Based on this real-time traffic volume data and the classic delay calculation method based on queuing theory, the delays caused by maintenance operations at different start time can be calculated and compared, and therefore the optimal maintenance operation start time can be obtained. The feasibility of the real-time traffic status data to real-time traffic volume data conversion method and the feasibility of optimizing the maintenance operation start time based on real-time traffic map data are verified by actual cases.
In China’s expressway work zones, it is a common phenomenon for drivers to have a low compliance rate with speed-limit instructions. Existing microscopic traffic simulation calibrations mainly focus on car-following and lane-changing behaviors, lacking research on speed-limit compliance behavior. Therefore, this paper proposes a method for collaborative calibration of the key parameters of a “car-following, lane-changing, speed-limit compliance” three-layer model based on the SUMO simulation platform. The research selects the key parameters in the IDM car-following model, LC2013 lane-changing model, and speed-limit compliance model to form a calibration parameter set, taking the time-mean speed and space-mean speed as optimization indicators, using the simultaneous perturbation stochastic approximation (SPSA) algorithm combined with a restart strategy, and aiming to minimize the root-mean-square error (RMSE) of the speed between the simulated and observed data for global optimization. The model is verified by the measured traffic flow and speed data in the expressway work zone. The verification results show that the three-layer calibration framework incorporating the speed-limit compliance model not only improves speed fitting but also better reproduces the distributional characteristics of real traffic flow in the work zone, especially the dispersion and heterogeneity of operating speeds. This research fills a gap in research involving SUMO calibration of speed-limit compliance in China and provides a theoretical basis and method-based support for microscopic simulation considering driver differences in speed-limit compliance.