Dae-Hyun Cho

Prof. Dae-Hyun Cho

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 February 2019 in Nanomaterials
Verified
Journal Article
Open access
PDF file
DCDae-Hyun Cho
Dae-Hyun Cho
JJJaehyuck Jung
Jaehyuck Jung
CKChan Kim
Chan Kim
JLJinhwan Lee
Jinhwan Lee
SOSe-Doo Oh
Se-Doo Oh
CLChanggu Lee
Changgu Lee
In the present study, dry friction and wear properties of atomically thin CVD-grown graphene and MoS2 films on SiO2/Si substrates were compared at low (72 MPa) and high (378 MPa) contact pressures. Analysis of atomic force microscopy images of these films verified that the MoS2 films, which were directly grown on the SiO2/Si substrates, had clean surfaces and made conformal contacts with the substrates. In contrast, the graphene film showed many contaminants on its surface and was loosely bonded with its SiO2/Si substrate due to its wet transfer from a Cu foil to the substrate. The MoS2 film exhibited friction and wear properties superior to those of the graphene film both at low and high contact pressures. We found that the clean sliding surface and strong bonding with SiO2/Si were the main causes of the superiority of the MoS2 film compared to the graphene film. Mild wear occurred in a layer-by-layer fashion at low contact pressure for the MoS2 film. At high contact pressure, severe wear occurred due to failure at the boundary between the MoS2 films and the underlying substrates. At both contact pressures, friction did not increase immediately after the removal of the MoS2 film from the SiO2/Si substrate because the film transferred onto the counter sliding surface and served as a lubricant.

17 October 2022 in Polymers
Verified
Journal Article
Open access
PDF file
RHRizwan Ul Hassan
Rizwan Ul Hassan
SKShaheer Mohiuddin Khalil
Shaheer Mohiuddin Khalil
Saeed Ahmed KhanSaeed Ahmed Khan
Saeed Ahmed Khan
SAShahzaib Ali
Shahzaib Ali
JMJoonkyeong Moon
Joonkyeong Moon
Doyoung ByunDoyoung Byun
Doyoung Byun
In the field of soft electronics, high-resolution and transparent structures based on various flexible materials constructed via various printing techniques are gaining attention. With the support of electrical stress-induced conductive inks, the electrohydrodynamic (EHD) jet printing technique enables us to build high-resolution structures compared with conventional inkjet printing techniques. Here, EHD jet printing was used to fabricate a high-resolution, transparent, and flexible strain sensor using a polydimethylsiloxane (PDMS)/xylene elastomer, where repetitive and controllable high-resolution printed mesh structures were obtained. The parametric effects of voltage, flow rate, nozzle distance from the substrate, and speed were experimentally investigated to achieve a high-resolution (5 µm) printed mesh structure. Plasma treatment was performed to enhance the adhesion between the AgNWs and the elastomer structure. The plasma-treated functional structure exhibited stable and long strain-sensing cycles during stretching and bending. This simple printing technique resulted in high-resolution, transparent, flexible, and stable strain sensing. The gauge factor of the strain sensor was significantly increased, owing to the high resolution and sensitivity of the printed mesh structures, demonstrating that EHD technology can be applied to high-resolution microchannels, 3D printing, and electronic devices.

13 February 2023 in ACS Applied Polymer Materials
Verified
Journal Article
Closed access
BIBusi Im
Busi Im
FPFariza Dian Prasetyo
Fariza Dian Prasetyo
HYHadi Teguh Yudistira
Hadi Teguh Yudistira
SKShaheer Mohiuddin Khalil
Shaheer Mohiuddin Khalil
DCDae-Hyun Cho
Dae-Hyun Cho
Doyoung ByunDoyoung Byun
Doyoung Byun

23 August 2024 in Energy & Environmental Science
Verified
Journal Article
Open access
PDF file
JMJoonkyeong Moon
Joonkyeong Moon
Seoung-Ki LeeSeoung-Ki Lee
Seoung-Ki Lee
BIBusi Im
Busi Im
Doyoung ByunDoyoung Byun
Doyoung Byun
DCDae-Hyun Cho
Dae-Hyun Cho
The demand for self-powered devices, particularly in biomedical and wearable technology, emphasizes efficient powering from ultralow-frequency vibrations. While triboelectric nanogenerators have shown potential, they still face challenges in powering below 0.1 Hz and suffer from tribological issues. Herein, we introduce a novel nanogenerator capitalizing the strain-dependent characteristics of the work function of gold. Our device achieves efficient power generation at 0.01 Hz, with a current density of 2.3 mA m−2, marking a significant breakthrough. At 0.5 Hz, it reaches 4.8 mA m−2, demonstrating substantial improvement over prior performance. Moreover, by eliminating repetitive contact-separation processes found in triboelectric nanogenerators, our generator exhibits no performance degradation due to tribological damage after 1 000 000 cycles. Integrated into a watch strap, it powers LEDs and generates Morse code signals via finger grasping, offering an innovative method for distress communication when conventional power sources are unavailable. The wide material selectivity for strain-modifiable work functions suggests promising research avenues.

26 November 2025 in Materials Science and Engineering: R: Reports
Verified
Journal Article
Open access
SAShahzaib Ali
Shahzaib Ali
SKShaheer Mohiuddin Khalil
Shaheer Mohiuddin Khalil
FSFaisal Shahzad
Faisal Shahzad
BIBusi Im
Busi Im
THTanveer Hussain
Tanveer Hussain
Doyoung ByunDoyoung Byun
Doyoung Byun

10 April 2023 in Applied Surface Science
Verified
Journal Article
Closed access
DCDae-Hyun Cho
Dae-Hyun Cho
SPSunyoung Park
Sunyoung Park
BIBusi Im
Busi Im
YKYoungchan Kim
Youngchan Kim
SKSang-Woo Kim
Sang-Woo Kim
Doyoung ByunDoyoung Byun
Doyoung Byun