Qiulin Niu

Prof. Dr. Qiulin Niu

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 December 2021 in Machining Science and Technology
Verified
Journal Article
Closed access
QNQiulin Niu
Qiulin Niu
LJL. Jing
L. Jing
ZYZ. Yu
Z. Yu
CLC. P. Li
C. P. Li
XQX. Y. Qiu
X. Y. Qiu
TKT. J. Ko
T. J. Ko
Silicon carbide particulate-reinforced aluminum (SiCp/Al) composites is one of the typical difficult-to-cut materials, which are not suitable well for traditional machining any more. In order to explore new processing technology and verify its feasibility, this paper discussed the effects of cryogenic assisted milling with liquid nitrogen (LN2) coolant on the machinability of SiCp/Al composites. The effects of cryogenic milling were also compared with that of conventional dry milling. The results showed that cryogenic milling of 20% SiCp/Al composites would increase the surface hardness of the material, causing 15% higher amount of cutting force in cryogenic milling as compared to dry milling. In addition, there were serious tool feed marks on the machined surface under cryogenic condition because of the secondary cutting mechanism, which resulted in high surface roughness and poor surface quality. Overall, 46.73% higher roughness Ra and 31.53% roughness Rz were seen for cryogenic milling in comparison with dry milling technique respectively. The dish angle of milling tool and processing environment plays important roles in machined surface. Chip brittleness increased and short arc chips were formed in cryogenic milling. It was suggested that milling SiCp/Al composites under cryogenic condition had negative effects on the machinability of the material.

17 December 2019 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
QNQiulin Niu
Qiulin Niu
LJLu Jing
Lu Jing
CWChunhao Wang
Chunhao Wang
SLShujian Li
Shujian Li
XQXinyi Qiu
Xinyi Qiu
DXDaohui Xiang
Daohui Xiang

7 April 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
QNQiulin Niu
Qiulin Niu
LJLu Jing
Lu Jing
CLChangping Li
Changping Li
ZYZhen Yu
Zhen Yu
SLShujian Li
Shujian Li
WYWenhui Yue
Wenhui Yue

1 August 2022 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
LJLu Jing
Lu Jing
QNQiulin Niu
Qiulin Niu
DZDilei Zhan
Dilei Zhan
SLShujian Li
Shujian Li
WYWenhui Yue
Wenhui Yue

18 August 2022 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
LJLu Jing
Lu Jing
QNQiulin Niu
Qiulin Niu
JDJiaqiang Dang
Jiaqiang Dang
QAQinglong An
Qinglong An
CWChunhao Wang
Chunhao Wang
TKTae Jo Ko
Tae Jo Ko

28 September 2024 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
QNQiulin Niu
Qiulin Niu
MWMeiyi Wu
Meiyi Wu
LLLipeng Liu
Lipeng Liu
JGJingyi Gao
Jingyi Gao
LJLu Jing
Lu Jing