Intense shock boundary-layer interaction may lead to multiple unstart modes existing in a hypersonic inlet. Thus, self-start problems become complex and cannot be explained using the classical double-solution theory of air inlet. The essence of the self-start process of a hypersonic inlet is the vanishment of separations near or in the inlet. To clarify self-start characteristics, experiments were conducted on three distinct types of unstart mode: the flow mode of small separation on body (SSB), large separation on body (LSB), and dual separations on both body and lip (DSBL); researchers recently discovered these as the unstart modes of hypersonic inlet. The results from the current experiment are as follows: (1) The SSB vanishes by raising the angle of attack (alpha). Before the vanishing point is reached, there is a dwindling process for this separation. (2) The LSB vanishes through acceleration or a decreasing alpha. (3) DSBL are difficult to vanish directly, which results in poor self-start performance. However, the DSBL flow mode may convert to LSB unstart form—which is easier to self-start—by decreasing the alpha. The Flow Field Reconstruction Method was designed to improve the self-start of the DSBL flow mode, and it was validated through experiments. Analysis of the flow mechanism revealed the reason for the poor self-start performance of the DSBL unstart mode: large-scale separation on the lip side cannot be promoted to vanish through broadwise spillage due to the resistance of sideboards. The results of this study could greatly enrich the existing theory of start problems for hypersonic inlets.
Experiments were conducted in this study to reveal the flow characteristics of a variable cross-section S-shaped isolator, when applying the steady-state back pressure at the isolator outlet. The self-excited oscillation characteristics of the shock train generated under the influence of steady-state back pressure at an incoming flow speed of Mach 2, were also studied. The findings suggest that pressure oscillation within the area affected by the shock train’s flow field was significantly more potent than outside the affected area. Moreover, the forward movement velocity of the shock train in the variable cross-section S-shaped isolator was not uniform. The forward movement speed was slower when encountering sharp turns and faster during gentle turns. In the shock train flow field, high-frequency pressure oscillations, which mainly stemmed from the oscillations of the separated shock legs, propagated more readily within the flow field than low-frequency pressure oscillations. The significant separation of the shock train flow field will switch between the top and bottom walls, and the frequency of pressure oscillation in the large separation region is low. On another note, the closer the distance between two points is in the shock flow field, the stronger the coherence of pressure oscillations will be. In the distance upstream of the shock train flow field, the turbulent boundary layer (TBL) determines pressure oscillations instead of the shock train flow field, so the coherence was very high.
1 December 2022 in Journal of Physics: Conference Series
In this paper, the shock train in the isolator is taken as the research object, and the method of detecting the leading edge position of the shock train during self-excited oscillation and forced oscillation is studied by conducting the wind tunnel test. A steady-state throttling system and a fluctuating throttling system are designed to apply the required steady-state and fluctuating back pressure downstream of the isolator. Then, the four methods of pressure ratio method, pressure difference method, standard deviation method, and Fast Fourier Transform (FFT) analysis method are used to detect and study the position of the shock train leading edge under steady and fluctuating back pressure to verify their applicability. The results show that under the condition of steady-state back pressure, the four methods can get effective results, and the results are consistent. Under the condition of fluctuating back pressure, the pressure difference method could not give effective results, but the other three methods could give effective and consistent results. And the results of the standard deviation method and the Fast Fourier Transform analysis method are similar in image and principle.
The shock wave/boundary layer interaction phenomenon in hypersonic inlets, affected by background waves, may induce the formation of multiple separation zones. Existing theories prove insufficient in explaining the underlying flow mechanisms behind complex phenomena arising from multi-separation zone interactions, which necessitates further investigation. To clarify the governing factors in multi-separation zone interactions, this study developed a simplified dual-separation-zone model derived from inlet flow field characteristics. A series of numerical simulations were conducted under an incoming flow at Mach 3 to systematically analyze the effects of internal contraction ratio, the influencing locations of expansion waves, and incident shock wave intensity on the mergence and re-separation of dual separation zones. The results demonstrate that both the expansion wave impingement position and incident shock intensity significantly influence specific transition points in dual-separation-zone flow states, though they do not fundamentally alter the evolutionary patterns governing the merging/re-separating processes. Furthermore, increasing incident shock intensity leads to the expansion of separation zone scales and prolongation of the dual-separation-zone merging distance.
1 August 2025 in Journal of Physics: Conference Series
This study employs numerical simulation methods to investigate the flow characteristics of hypersonic inlets with different aspect ratio configurations under unstart conditions. Through comprehensive analysis of shock wave structure evolution, wall pressure distribution characteristics, and key performance parameters including mass flow ratio and total pressure recovery coefficient, the influence mechanism of aspect ratio on inlet unstart modes is revealed. The results demonstrate three distinct unstart modes: small separation on body (SSB), large separation on body (LSB), and dual-separation on both body and lip (DSBL). Furthermore, as the aspect ratio increases, the broadwise spillage effect weakens, and when exceeding a critical value, the DSBL transitions to LSB flow mode. Increasing the aspect ratio reduces the self-start performance of inlet while simultaneously improving key performance indicators such as pressure ratio, mass flow ratio and total pressure recovery coefficient, which provides important theoretical support for the design and optimization of hypersonic inlets.
The aft-body mounted inlet of a hypersonic vehicle has garnered attention for its potential to shorten the propulsion system. This study aims to explore the influence of compression direction on the performance of the hypersonic inlet attached to the vehicle’s aft body. To achieve this objective, a simplified, integrated model of the body and two-dimensional inlet was developed and evaluated using numerical simulation techniques. The study conducted a comparative analysis of the overall and starting performance between inverted and normal inlet layouts while ensuring uniformity in inlet configuration and installation location. The results indicated that the inverted layout surpassed the normal layout in terms of airflow capture capabilities, with an 8.24% higher mass flow rate. However, the inverted inlet layout exhibited an 11.46% reduction in total pressure recovery performance compared to the normal layout. Additionally, the study found that the inverted inlet layout demonstrated a self-starting Mach number 1.62 lower than that of the normal inlet layout. This difference stemmed primarily from the pressure gradient on the body surface induced by the incident shock wave of the inverted inlet, which enhanced starting performance by eliminating low-energy flow near the wall.