Natural biopolymers are an interesting resource for edible films production, as they are environmentally friendly packaging materials. The possibilities of the application of main animal proteins and natural polysaccharides are considered in the review, including the sources, structure, and limitations of usage. The main ways for overcoming the limitations caused by the physico-chemical properties of biopolymers are also discussed, including composites approaches, plasticizers, and the addition of crosslinking agents. Approaches for the production of biopolymer-based films and coatings are classified according to wet and dried processes and considered depending on biopolymer types. The methods for mechanical, physico-chemical, hydration, and uniformity estimation of edible films are reviewed.
1 March 2008 in Bulletin of Experimental Biology and Medicine
The development of approaches for the non-thermal sterilization of instruments is an urgent task to ensure the safety of meat industry products, where the use of hot water leads to the formation of condensates and a deterioration in the hygienic condition of the premises. In this study, an installation for sterilizing knives was created, which works by activating aqueous salt solutions with a glow discharge. The power consumption of the installation reactor is only 125–150 Wh. The temperature rise of the sterilizing agent used is about 1.1 ± 0.2 °C/min/L. The effectiveness of the installation for plasma-activation of aqueous solutions of chloride and sodium sulfate by glow discharge (PAW) in relation to the inactivation of microorganisms, including Staphylococcus aureus, Salmonella typhimurium, Pseudomonas gessardii and L. monocytogenes, on steel surfaces was evaluated. Samples of stainless steel (parts of knives) were used in two versions (new and artificially aged). Mono- and polyspecies bacterial biofilms were grown on the surface of the samples. The treatment was carried out by immersing samples of steel plates in plasma-activated aqueous solutions. It was found that the treatment of plates in a knife sterilizer for 1 min had an effective effect on the inhibition of all types of studied bacteria.
Objectives. This study evaluates the effect of the modification process on the group composition of bitumen and bitumen binders containing rubber powder and hybrid modifier that is based on styrene–butadiene thermoplastic elastomer and rubber crumb. The aim of the study was to determine the presence or absence of functional groups that reflect the direction of physicochemical processes during the preparation of a hybrid modifier in rotary dispersers and during the modification of bitumen binders. Methods. Rubber powder and hybrid modifier were obtained by high-temperature shear grinding using a rotary disperser. Bitumen and modified bitumen binders were investigated via Fouriertransform infrared spectroscopy. Using the method of spectral subtraction, it was determined that during the process of manufacturing modified bitumen binders, structural changes occur in both bitumen and modifiers. During this study, the extraction of modifiers (rubber powder and hybrid modifier) in toluene was performed. Results. The quantitative analysis of changes in the group composition of modifiers before and after the modification procedure was carried out. The active polymer and structural indices were determined. The general trend of the change in the active polymer and structural indices was noted for the initial spectra of the rubber powder and hybrid modifier, and their spectra were obtained after the procedure of subtraction from the spectra of bitumen binders. Conclusions. The interdiffusion of aromatic compounds between the bitumen component and modifier particles was confirmed. On the basis of the results of the extraction of modifiers in toluene, and by taking into account the infrared spectroscopy data, it was determined that during the production of hybrid modifier during the simultaneous grinding of rubber crumb and styrene– butadiene thermoplastic elastomer, there was a chemical interaction between them.
1 September 2019 in IOP Conference Series: Earth and Environmental Science
Reduction of fat in meat products is an important task aimed at solving the problem of excessive fat intake. Different substances are used as fat replacers: plant and animal proteins, and polysaccharides. The aim of the research was a comparative study of the effect of different fat replacers (inulin; a mixture of hydrocolloids; soy protein, and; collagen protein) on the quality of low-fat cooked sausage. In the experimental samples, 50% of backfat was replaced with: inulin gel (exp. 1), a mixture of hydrocolloids (carrageenan, xanthan gum and guar gum) with additional incorporation of water (exp. 2), hydrated soy protein (exp. 3), or hydrated collagen protein (exp. 4). Addition of the fat replacers reduced the fat content by more than 40%. The use of hydrocolloids and soy protein in the hydrated form as fat replacers negatively affected sausage taste and consistency. Addition of the hydrated animal protein had no significant effect on taste, color characteristics, or water activity, but led to a decrease in the sausage shear force. The sausage produced with inulin had the organoleptic, color and strength characteristics closest to the control sausage. Inulin gel, therefore, is recommended as a fat replacer in cooked sausages.
5 November 2016 in Journal of Analytical Chemistry
We present the results of determination of unsaturated fatty acids (FAs) in foods of animal origin. It is shown that, in addition to the main component, monounsaturated cis-9-octadecenoic (oleic)...