A compact, low-profile, dual-band (2.4/5.8 GHz) omnidirectional circularly polarized (CP) antenna for consumer Unmanned Aerial Vehicle (UAV) communications is proposed. Given the constraints of UAV installation, we incorporate complex miniaturization etching techniques into the antenna design. The low-frequency resonance is primarily realized by four short-terminated arcs, while the high-frequency resonance is predominantly induced by four open-terminated branches. In addition, a dual-band coupled strip-line filter is cascaded to the radiator, enhancing the design's bandwidths. A prototype of the antenna is simulated, fabricated, and measured, resulting in final dimensions of 0.2 × 0.2 × 0.042λ 03 (λ 0 is the free-space wavelength at 2.4 GHz). The -10 dB | S 11 | and 3 dB Axial Ratio (AR) overlapped bandwidths reach 40 and 125 MHz for the low- and high-frequency bands, respectively. Lastly, we present an example of integrating the antenna into a quadcopter UAV and briefly discuss the potential of applying this antenna for a Multiple-Input, Multiple-Output (MIMO) system.
13 September 2022 in IEEE Antennas and Wireless Propagation Letters
This letter presents a folded reflectarray (FRA) capable of electrical beam steering in the Ka-band. The FRA consists of a low-profile feeding source, a dual-layer wire grid, and 36×36 polarization twisting reflective elements. An element of center shorted patch with two plated through holes is proposed where only two switches are required for polarization twisting and 1-bit encoding. A cavity is then introduced surrounding the element to improve the beam-steering performance. To verify the proposed element, two prototypes with 0° and 60° beam directions are designed and experimented where the metal stub and open circuit are used to model “ on/off ” states of PIN diodes for simplification. The measured peak gain of 0°FRA is 27.5 dBi with 2 dB gain bandwidth of 28–32 GHz (13.3%). A measured gain drop of 3.25 dB is achieved by the 60°FRA, which verifies the wide-angle beam-steering ability. The measured reflection coefficient of the feeding source is less than −15 dB over the operating band. The proposed FRA has a good potential to realize beam-steering with real PIN diodes for the satellite communications.
18 October 2023 in IEEE Antennas and Wireless Propagation Letters
This letter proposes a wideband metasurface (MTS) inspired circularly polarized (CP) antenna array working in Ka-band, which consists of 2×2 antenna subarrays fed by a sequential-rotation (SR) network. The MTS radiator consisting of a 2×2 rectangular patch with a cross patch embedded in the center is applied to contribute two CP modes for wideband operation with the help of characteristic mode analysis. An I-shaped slot located on the ground plane is employed as the coupling excitation for the CP radiation. To further enhance CP bandwidth, MTS-antennas sequentially rotated by 90° are incorporated with the SR network which outputs uniform orthogonal phased signals. To verify the proposed design, several prototypes are fabricated and measured. The results show an impedance bandwidth of 25-37.2 GHz (39.35%) and 25-38.05 GHz (41.4%) for 4×4 and 8×8 arrays respectively, while a 3 dB axial ratio bandwidth of 26.5-35.5 GHz (29%) and 26.5-34.5 GHz (26.3%) are realized. The peak gain of 17.51 dBic and 20.82 dBic are achieved in the vicinity of 30 GHz.
17 April 2024 in IEEE Transactions on Antennas and Propagation
This paper presents a proposal for a 3-D printed all-metal conformal circularly polarized reflectarray antenna operating in the X-band. The reflectarray element is constructed with a quasi-I-shaped arm with a pillar at the center as support. To enhance the angular stability of the reflection response for oblique incidence, twelve metal blocks are introduced around the element. Additionally, a compact wideband 3-D printed circularly polarized horn antenna is designed as the feeding source. A novel method for estimating the aperture efficiency of the conformal reflectarray is derived to determine the reflection phase distribution of the reflectarray and the position of the feeding antenna. To validate the proposed reflectarray element and approach, an all-metal 15×15 3-D printed conformal reflectarray is designed, fabricated, and measured. The experimental results demonstrate a 42.3% (8.2-12.6 GHz) 3 dB axial ratio bandwidth, a 11.4% (10.4-11.6 GHz) 1 dB gain bandwidth, a 27% (9.6-12.6 GHz) 3 dB gain bandwidth, and a 40.7% aperture efficiency.
The hollow metal waveguides are attractive components for millimeter-wave circuits owing to low loss. To integrate with the front-end circuit, a transition from microstrip line to waveguide is required. In this article, a microstrip-to-waveguide transition is presented in the W-band by using an E-plane probe with a parasitic patch. The probe is embedded into the waveguide along the center of the broad wall to excite the TE10 mode. A backshort-circuited waveguide with a quarter wavelength is used to obtain sufficient energy coupling and achieve good impedance matching. The additional parasitic patch can introduce a new resonance at a low frequency to enhance the working bandwidth. Hence, the proposed transition achieves wide working bandwidth and low insertion loss. For verification, a back-to-back transition is constructed and measured. The measured results indicate that the proposed transition has a wide working bandwidth covering the entire W-band. The measured reflection coefficient is below −13 dB from 70 to 110 GHz and the average insert loss is 1.1 dB. Attributed to wide working bandwidth and simple structure, the proposed transition is attractive for W-band circuit systems.
Recently, hybrid logic circuits based on magnetic tunnel junctions (MTJs) have been widely investigated to realize zero standby power. However, such hybrid CMOS/MTJ logic circuits suffer from a severe sensing reliability due to the limited tunnel magnetoresistance ratio (TMR ≤ 150%) of the MTJ and the large process variation in the deep sub-micrometer technology node. In this paper, a novel differential sensing amplifier (DSA) is proposed, in which two PMOS transistors are added to connect the discharging branches and evaluation branches. Owing to the positive feedback realized by these two added PMOS transistors, it can achieve a large sensing margin. By using an industrial CMOS 40 nm design kit and a physics-based MTJ compact model, hybrid CMOS/MTJ simulations have been performed to demonstrate its functionality and evaluate its performance. Simulation results show that it can achieve a smaller sensing error rate of 9% in comparison with the previously proposed DSAs with a TMR ratio of 100% and process variation of 10%, while maintaining almost the same sensing delay of 74.5 ps and sensing energy of 1.92 fJ/bit.