Hongmin Meng

Mr. Hongmin Meng

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 May 2018 in IEEE Transactions on Sustainable Energy
Verified
Journal Article
Closed access
XXXiaowen Xing
Xiaowen Xing
HMHongmin Meng
Hongmin Meng
LXLili Xie
Lili Xie
LYLei Yue
Lei Yue
ZLZhongwei Lin
Zhongwei Lin
A wind energy conversion system is mainly operated in a partial-load region and a full-load region. In the partial-load region, the primary objective is to maximize energy conversion efficiency, whereas the main goal is maintaining the output power at the rated level in the full-load region. The two control regions are switched in accordance with prevailing wind speed. However, steep and large changes of generator power, as well as mechanical loads, may be experienced during switching transient, which bring about negative impacts on power system reliability and turbine lifetime. This paper presented an advanced model-predictive control considering switching performance improvement. The proposed method not only achieved the control objectives in both two control regions, but also mitigated uncertain power fluctuations and mechanical loads during control mode switching. This high switching performance benefited from the presented dynamic switching transient process driven by the defined wind speed crossing events. During switching transient, system operating states were transferred along with the proposed dynamic vector. Small-signal analysis was employed to prove the good stability and dynamic performance of the system in switching transients. Simulation and hardware-in-the-loop experimental studies verified the effectiveness of the proposed method.

6 July 2017 in Energies
Verified
Journal Article
Open access
PDF file
HMHongmin Meng
Hongmin Meng
TYTingting Yang
Tingting Yang
JLJi-Zhen Liu
Ji-Zhen Liu
ZLZhongwei Lin
Zhongwei Lin
In wind turbine control, maximum power point tracking (MPPT) control is the main control mode for partial-load regimes. Efficiency potentiation of energy conversion and power smoothing are both two important control objectives in partial-load regime. However, on the one hand, low power fluctuation signifies inefficiency of energy conversion. On the other hand, enhancing efficiency may increase output power fluctuation as well. Thus the two objectives are contradictory and difficult to balance. This paper proposes a flexible MPPT control framework to improve the performance of both conversion efficiency and power smoothing, by adaptively compensating the torque reference value. The compensation was determined by a proposed model predictive control (MPC) method with dynamic weights in the cost function, which improved control performance. The computational burden of the MPC solver was reduced by transforming the cost function representation. Theoretical analysis proved the good stability and robustness. Simulation results showed that the proposed method not only kept efficiency at a high level, but also reduced power fluctuations as much as possible. Therefore, the proposed method could improve wind farm profits and power grid reliability.

22 September 2023
Verified
Conference Paper
Open access
YZYang Zhao
Yang Zhao
ZLZesan Liu
Zesan Liu
ZXZhenan Xu
Zhenan Xu
MWMengqiang Wang
Mengqiang Wang
HMHongmin Meng
Hongmin Meng
WJWenhao Jia
Wenhao Jia
Simulation technology is widely used in the entire life cycle of power systems such as planning and design, commissioning and testing, operation and maintenance, and plays an important and irreplaceable role. With the rapid development of new power systems, energy simulation platforms characterized by multi-time scales, platformization, and intelligence are in urgent need of development and application. This article introduces the design and implementation of a web -based universal energy simulation modeling component. The component interface is based on the power automation standard IEC 61970. It can be integrated with industry application software or platforms to provide open equipment management and graphical modeling. function, and can integrate any energy analysis algorithm based on component output format to provide support for the planning and research of new power systems.

24 September 2023
Verified
Conference Paper
Open access
GZGuangyang Zhou
Guangyang Zhou
Shaahin FilizadehShaahin Filizadeh
Shaahin Filizadeh
ZLZesan Liu
Zesan Liu
HMHongmin Meng
Hongmin Meng
XZXueying Zhuge
Xueying Zhuge
ZXZhenan Xu
Zhenan Xu
A single-ended fault detection scheme for long transmission lines in MTDC girds based upon an artificial neural network (ANN) is proposed. The method overcomes existing detection difficulties in protection of long transmission line resulting from high grounding resistance and attenuation, and also avoids the sophisticated threshold value selection process. The amplitude of the zero-mode set of the positive-sequence voltage and high-frequency components of the voltage traveling wave extracted by a wavelet transform are the two inputs to an ANN. The output of the ANN determines the fault type. A model of a four-terminal dc grid with overhead transmission lines is built in PSCAD/EMTDC. EMT simulations results from this model confirm that the proposed method achieves 100% accuracy in detecting short-circuit faults with high resistance on long lines; the method eliminates mal-operation of DC circuit breakers when faced with power order changes or ac side faults. Its robustness is also assessed and shown to have no perceptible effect on the accuracy of the detection scheme, thus ensuring its reliability and stability.