Afeni Thomaa Busuyi

Dr. Afeni Thomaa Busuyi


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2019 in Mining of Mineral Deposits
Verified
Journal Article
Open access
FAFederal University of Technology Akure
Federal University of Technology Akure
ROR.A Osemenam
R.A Osemenam
ABAfeni Thomaa Busuyi
Afeni Thomaa Busuyi
VAV.A Alfred
V.A Alfred
ALAjaokuta West African Ceramics Ltd
Ajaokuta West African Ceramics Ltd
UHUniversity of Port Harcourt
University of Port Harcourt

1 January 2020 in Mining of Mineral Deposits
Verified
Journal Article
Closed access
ABAfeni Thomaa Busuyi
Afeni Thomaa Busuyi
EOEmmanuel O. Okeleye
Emmanuel O. Okeleye

19 June 2018 in Aspects in Mining & Mineral Science
Verified
Journal Article
Open access
ABAfeni Thomaa Busuyi
Afeni Thomaa Busuyi
IAIdris Musa A
Idris Musa A
UMUsman Mariam
Usman Mariam

1 January 2020 in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
Verified
Journal Article
Closed access
AAA.P Akinola
A.P Akinola
ABAfeni Thomaa Busuyi
Afeni Thomaa Busuyi
ROR.A Osemenam
R.A Osemenam
Purpose. To determine the geoid heights from various control points of the quarry located in the northern and southern zones of the limestone deposit of the Lafarge WAPCO Cement Ewekoro in Ogun State, Nigeria. Methodology. The GPS and levelling data were used to determine the geoid heights from various control points of the quarry located in the northern and southern zones of the limestone deposit. The geoid heights obtained from GPS-Levelling data were used for three surface models which are polynomial regression model, inverse distance model and nearest neighbour model. These models were used to crossvalidate the geoid heights for the control points. Findings. The result shows that the deviations of the geoid heights for the GPS/Levelling and models are between 0.03 and 0.01m respectively. The models were used to generate contour maps that reveal the better location where the flood can be channelled. Originality. The results can be compared to the data obtainable during operations carried out in the quarry. Practical value. The flood in the quarry face will be better controlled by creating a sump at the lowest point on the elevation maps and controlled drilling to give better aeration.

30 June 2024 in ABUAD Journal of Engineering and Applied Sciences
Verified
Journal Article
Open access
PDF file
ABAfeni Thomaa Busuyi
Afeni Thomaa Busuyi
AAAdedapo Adeyemi
Adedapo Adeyemi
KMKolawole Tajudeen Mohammed
Kolawole Tajudeen Mohammed
This research investigated the mine plans used for the production target and annual production of limestone for the past seven (7) years. The actual amount of limestone produced per year in tons was computed to determine the variations in the mine's production and the life span of the reserve of limestone deposits. A new mine plan was proposed, and a targeted amount of limestone production per year was suggested. The mine plans for the mine's production were generated from 2014 to 2020 using a complete data collection system for Real Time (RTK) GPS and Total Stations with in-field coordinate geometry called SurCE by Carlson Software. The total production target for the seven (7) years was 87,017,146 tons and the actual production was 76,313,056 tons. The total variations for the years under this assessment were -10,704,090 tons except for the year 2018 when the actual production was higher than the production target of 511,179 tons. The volumetric reserve estimation revealed that the total volume of the limestone reserve is 5,052,236,090.186 tons. The expected production per week was computed to be 356,400 tons/week, expected monthly production, (EMP) was estimated to be 1,425,600 tons/month. The expected production year, (EPY) was 17,107,200 tons/year and the life span of the limestone deposit, (LS) was computed to be 295.34 years. It can be suggested that the company should target a production rate of 1,425,200 monthly and 17,104,200 per year. This suggestion can be achieved if there is enough investment in terms of skilled labour, heavy-duty machinery, and equipment which will cost-effectively boost production.

12 February 2026 in Engineering Headway
Verified
Conference Paper
Closed access
PDF file
BABabatunde Adebayo
Babatunde Adebayo
ABAfeni Thomaa Busuyi
Afeni Thomaa Busuyi
DADamilola J. Afu
Damilola J. Afu
OOOlaoluwa B. Ogunyemi
Olaoluwa B. Ogunyemi
AOA. O. Omoseebi
A. O. Omoseebi
AOAlexander Orunduyi
Alexander Orunduyi
Abrasive properties of selected rocks and their influence on button bit wear were investigated. Rock samples were obtained from three locations in Southwest, Nigeria. These samples were tested in the laboratory for grain size and circularity factor. Also, porosity, Equivalent Quartz content (EQC), Rock Hardness Number (RHN), Rock Abrasivity Index (RAI) and Uniaxial Compressive Strength were determined. Bit button lengths consumed were measured at regular interval as drilling operation progresses. Results of grain size revealed that medium feldspar granite has least average grain size varying from 0.12 – 0.14 mm. There is possibility that rate of drilling may be low while drilling through this rock. The values of circularity factor varied from 0.624 for medium feldspar granite to 0.786 for coarse muscovite granite . The mean values of porosity varied from between 0.85 and 1.33% for medium feldspar granite and coarse muscovite granite respectively. Biotite hornblende granite has the highest mean uniaxial compressive strength value of 119.48 MPa while coarse muscovite granite has the least mean value of 90.65 MPa. The values of free silica, EQC, RHN, and RAI varied from 35.93 – 51.35%, 45.60 – 67.21%, 575.52 – 821.64 kg/mm 3 and 4133.64 – 7003.71 respectively. It was observed that grain size affects the void size in these rocks, which accounted for least porosity value obtained in medium feldspar granite . Average bit button length consumed varied from 15.56 – 24.54 mm for gauge button while length of centre button varied from 13.00 – 19.61 mm. Higher gauge button length consumption could be inferred that it effects the cutting, crushing and wedging of rock mineral components at rock-bit interface. The understanding of grain size, circularity factor and abrasive properties will provide adequate information for quarry to select appropriate bit and drilling machine.