When an electric vehicle (EV) is driving at a very low or high speed, there are cases where energy recovery is not possible because the back electromotive force generated in the motor is too small or large. In this paper, we investigate the application of the regenerative electromagnetic retarder's energy recovery method to the permanent magnet synchronous motor (PMSM) of an EV. When the EV was driven downhill or coasts, L-C resonance via switched capacitor was used to control the voltage generated by the PMSM as a voltage that can recharge the battery. During regeneration, the voltage generated in the PMSM varied along with the degree of resonance through switching the duty of the proposed circuit. Through simulation, DC-Link voltage according to switching duty ratio and motor speed is plotted in a 3D map. Based on this, voltage control algorithm using PI and reverse PI duty control has been proposed. To prove the proposed algorithm, the DC-link stage of the inverter is simply equivalent to the R-C model. And, if the PMSM operates at a constant speed, the generated voltage is controlled so as to charge the battery. In addition, the discharging and charging energies of the battery are simulated when the EV with certain load torque is driving uphill and downhill. Considering the dynamics of the car, the energy recovery rate was simulated when the EV is driving uphill and downhill in a 50:50 ratio at the same slope and distance. The simulations were conducted using MATLAB Simulink, and the experiments were carried out using a motor-generator set and a small electric truck equipped with a 13 kW PMSM, respectively.
20 October 2016 in THE TRANSACTIONS OF KOREAN INSTITUTE OF POWER ELECTRONICS
In this paper, we study the method of increasing the energy recovery rate by controlling the voltage which generated by the electric vehicle at the regenerative braking. The method includes an L-C resonance circuit and voltage control to make the battery chargeable. Thus, it is possible to increase the energy recovery and eventually increases the travel distance of the EV. The voltage of the resonant circuit is analyzed using a proposed algorithm with PI and reverse-PI duty controller. Unlike the previous studies have verified the voltage control algorithm only through the simulation, the control algorithm was verified through the experiment using M-G set.
1 January 2020 in Advances in Science, Technology and Engineering Systems Journal
This paper proposes a novel and robust method of sensorless speed control using a deadbeat observer for an interior permanent magnet synchronous motor (IPMSM). The proposed sensorless speed control method uses a deadbeat observer to estimate the extended electromotive force (EEMF) in a rotational coordinate system. The estimated EEMF is used in the IPMSM velocity estimation algorithm. The deadbeat EEMF observer (DEEMFO) shows greater robustness compared to the reconstructor, which estimates the EEMF by simply recalculating the voltage equation. Unlike a reconstructor, DEEMFO has a feedback component, so it can compensate for errors due to uncertainty in motor parameters and errors due to parameter fluctuations that may occur during use. By simulating and experimenting with speed, load torque, and parameter fluctuations, it is proved to be more robust and precise than the reconstructor. The simulation is performed with MATLAB/Simulink, and the experiments were carried out using a DSP TMS320F28335 and a motor-generator set (M-G Set). The simulation and experiment results show the reliability and precision of the proposed sensorless control method.
In this paper, in order to maximize the energy recovery from an electric vehicle (EV) motor, we propose a new method to control the voltage generated by the permanent magnet synchronous motor (PMSM) of an EV. The method includes an L-C resonance circuit, and it controls the voltage to make the battery chargeable. Thus, it is possible to increase the energy recovery, which can increase the travel distance of the EV. The DC link voltage depends on the driving pulse of the control device. We analyzed the voltage of the resonance circuit, and to control this voltage, we proposed an algorithm using the PI duty controller. To verify this control algorithm, a simple simulator was constructed and simulated with a constant speed and the R-C circuit model. To make the simulations more realistic, we applied the load torque, which virtualizes the uphill and downhill driving of the vehicle. Simulation using the battery model was also conducted. The energy recovery rate was calculated, and the voltage control algorithm was verified.