Milena Koralnik

Milena Koralnik


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 October 2021 in Metallurgical and Materials Transactions A
Verified
Journal Article
Open access
PDF file
BABoguslawa Adamczyk–Cieslak
Boguslawa Adamczyk–Cieslak
MKMilena Koralnik
Milena Koralnik
RKRoman Kuziak
Roman Kuziak
KMKamil Majchrowicz
Kamil Majchrowicz
JMJarosław Mizera
Jarosław Mizera
This paper describes the development and characterisation of bainitic steel for rail applications based on carbide-free, low-alloy steel. The results show that after rolling and subsequently cooling, the designed carbide-free bainitic steel exhibits better mechanical performance than standard pearlitic steel. This is because of its fine, carbide-free bainitic microstructure, which consists of bainitic ferrite and retained austenite laths. Microstructural and mechanical property analysis was carried out using scanning and transmission electron microscopy, X-ray diffraction, hardness measurements, tensile and low-cycle fatigue tests. The obtained results demonstrate that during low cyclic deformation, a partial transformation of the retained austenite into deformed martensite α′ takes place, and strain-induced martensitic transformation occurs. The initial strengthening of the material during low-cycle fatigue was caused by the transformation of austenite into martensite and the increase in the dislocation density of the steel. In addition, an optimal amount of retained austenite in the form of thin layers and islands (dimensions not exceeding 1 µm) made it possible to obtain a high yield while maintaining the high plasticity of the steel. These microstructural features also contributed to the high crack resistance of the tested carbide-free bainitic steel.

4 January 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
ACAdamczyk- Cieślak
Adamczyk- Cieślak
BOBogusława
Bogusława
MKMilena Koralnik
Milena Koralnik
RKRoman Kuziak
Roman Kuziak
KMKamil Majchrowicz
Kamil Majchrowicz
JMJarosław Mizera
Jarosław Mizera
This paper presents the microstructural changes and mechanical properties of carbide-free bainitic steel subjected to various heat treatment processes and compares these results with similarly treated ferritic–pearlitic steel. A key feature of the investigated steel, which is common among others described in the literature, is that the Si content in the developed steel was >1 wt.% to avoid carbide precipitation in the retained austenite during the bainitic transformation. The phase identification before and after various heat treatment conditions was carried out based on microstructural observations and x-ray diffraction. Hardness measurements and tensile tests were conducted to determine the mechanical properties of the investigated materials. In addition, following the tensile tests, the fracture surfaces of both types of steels were analyzed. Changing the bainitic transformation temperature generated distinct volume fractions of retained austenite and different values of mechanical strength properties. The mechanical properties of the examined steels were strongly influenced by the volume fractions and morphological features of the microstructural constituents. It is worth noting that the bainitic steel was characterized by a high ultimate tensile strength (1250 MPa) combined with a total elongation of 18% after austenitizing and continuous cooling. The chemical composition of the bainitic steel was designed to obtain the optimal microstructure and mechanical properties after hot deformation followed by natural cooling in still air. Extensive tests using isothermal transformation to bainite were conducted to understand the relationships between transformation temperature and the resulting microstructures, mechanical properties, and fracture characteristics. The isothermal transformation tests indicated that the optimal relationship between the sample strength and total elongation was obtained after bainitic treatment at 400 °C. However, it should be noted that the mechanical properties and total elongation of the bainitic steel after continuous cooling differed little from the condition after isothermal transformation at 400 °C.

15 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
AWAntoni Wadowski
Antoni Wadowski
JWJan Wróbel
Jan Wróbel
MKMilena Koralnik
Milena Koralnik
RSRyszard Sitek
Ryszard Sitek
Interactions in a multicomponent Ni-Cr-Mo-Al-Re model alloy were determined by ab initio calculations in order to investigate the Re doping effect on Haynes 282 alloys. Simulation results provided an understanding of short-range interactions in the alloy and successfully predicted the formation of a Cr and Re-rich phase. The Haynes 282 + 3 wt% Re alloy was manufactured using the additive manufacturing direct metal laser sintering (DMLS) technique, in which the presence of the (Cr17Re6)C6 carbide was confirmed by an XRD study. The results provide useful information about the interactions between Ni, Cr, Mo, Al, and Re as a function of temperature. The designed five-element model can lead to a better understanding of phenomena that occur during the manufacture or heat treatment of modern, complex, multicomponent Ni-based superalloys.

11 October 2022 in Crystals
Verified
Journal Article
Open access
PDF file
TTTomasz Tokarski
Tomasz Tokarski
GCGrzegorz Cios
Grzegorz Cios
DMDorota Moszczyńska
Dorota Moszczyńska
BABoguslawa Adamczyk–Cieslak
Boguslawa Adamczyk–Cieslak
MKMilena Koralnik
Milena Koralnik
JMJarosław Mizera
Jarosław Mizera
Single crystals of Cu-8.% at. Al were subjected to cold drawing up to 1.1 true strain. Development of the crystallographic texture was analysed at various stages of the drawing process. Investigations revealed significant crystal rotation and reorientation due to a twinning process, while general 4-fold symmetry around the drawing direction was preserved. Local texture analysis performed on cross-sections perpendicular to the drawing direction showed that due to crystal rotation, the original crystal was initially fragmented into four quadrants. However, within the volume near the central axis the initial cubic orientation was preserved. Subsequent deformation within dominating twinning systems led to further fragmentation which divided the crystal into sectors one eighth the size of the full circular cross-section. The obtained results also indicate that approximation of the drawing process stress state by the tensor having only normal components cannot be used during analysis of the activation of deformation systems.