Improving the photogenerated carrier separation efficiency of individual semiconductor materials has always been a key challenge in photocatalysis. In this study, we synthesized a novel photocatalytic material, N-CQDs/UBWO, in situ by combining nitrogen-doped carbon quantum dots (N-CQDs) derived from discarded corn stover with ultrathin Bi₂WO₆ nanosheets (UBWO). Detailed characterization indicates that the random distribution of N-CQDs on the UBWO surface increases the specific surface area of UBWO, which is beneficial for the adsorption and degradation of oxytetracycline (OTC). More importantly, N-CQDs act as electron acceptors, promoting the effective separation of photogenerated charges, prolonging the lifetime of charge carriers in UBWO, and thereby enhancing the degradation efficiency of OTC. As a result, the optimized 3wt%N-CQDs/UBWO could degrade 85% of OTC within 40 min under visible light, with a removal rate four times that of pure Bi₂WO₆. The performance of photocatalytic degradation over OTC by 3wt%N-CQDs/UBWO exceeds that of most reported Bi₂WO₆-based photocatalysts. The EPR analysis confirmed that ∙O₂⁻ and ∙OH are the main active species in the photocatalytic degradation of OTC on 3wt%N-CQDs/UBWO. This study provides insight into designing green, low-cost, and efficient photocatalysts using CQDs derived from waste biomass and the degradation of emerging pollutants like antibiotics.

Piezoelectric photocatalysis improves catalytic activity by preventing photogenerated carrier recombination. Hence, three morphologies of BaTiO₃ (BTO) were successfully prepared for the piezoelectric photocatalytic degradation of tetracycline (TC, C_(TC) = 40 mg/L). The tetragonal-phase BaTiO₃ nanoparticles (BTO-NPs) showed the best performance in comparison with cubic-phase nanoflowers (BTO-Nf) and cubic-phase coral-like structures (BTO-Nc) under the same conditions (C_(BTO) = 0.6 g/L). When the loading of BTO-NPs was reduced to 0.2 g/L, the photocatalytic degradation efficiency was lowered from 64.2% to 50.1%. However, the 0.6 g/L BTO-NPs increased by only 12.8% after piezoelectricity induction. On the contrary, the BTO-NPs’ degradation effect of 0.2 g/L with the piezoelectric effect was greatly improved from 50.1% to 78.0%, with an increase rate of 27.9%. As the quantity of catalyst was decreased, the increased inter-particle voids made the lattice more susceptible to deformation by external forces, producing a more pronounced piezoelectric effect. These findings indicate that crystal structure and catalyst loading are critical factors in increasing piezoelectric photocatalytic performance. This article emphasizes the application value of piezoelectric photocatalysis in degrading organic pollutants, and provides practical guidelines for optimizing its performance.

Sunitinib malate, as an anticancer compound and a multi-targeted tyrosine-kinase inhibitor for treatment of glioma, was comprehensively studied by using different liquid chromatography methods. Since sunitinib malate shows Z-E isomerism, various reverse phase high performance liquid chromatography (RP-HPLC) programs were designed to access quantitative determination and good separation of Z-E stereoisomers. Moreover, some impurities including N-oxide and impurity B were to be separated from the main isomer with acceptable resolution. In the present work, different RP-HPLC programs were developed in which the type of mobile phase, flow rate, pH, and temperature were optimized to reach the best analysis conditions and control the rate of Z to E conversion. In addition, the effect of some operational parameters during the solution preparation including initial concentration of the analyte, temperature, pH, and type of solvent on the stability of Z isomer were investigated. The opted conditions for quantitative analysis were C8-Hector column as stationary phase, methanol as solvent, ammonium acetate buffer containing triethylamine as mobile phase, the pH of mobile phase of 8.5, the flow rate of 1.0 mL/min, and detection at 425 nm. In this situation the peaks of E and Z isomers were at 16.3 and 19.7 min. Full validation of the designed method was done based on ICH guidelines.