Shinichiro Adachi

Dr. Shinichiro Adachi

Osaka Research Institute of Industrial Science and Technology, Osaka 594-1157, Japan
orcid

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2010 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
TTTakeshi Terajima
Takeshi Terajima
FTFumiya Takeuchi
Fumiya Takeuchi
KNKazuhiro Nakata
Kazuhiro Nakata
Shinichiro AdachiShinichiro Adachi
Shinichiro Adachi
KNKoji Nakashima
Koji Nakashima
TITakanori Igarashi
Takanori Igarashi

28 June 2017 in Coatings
Verified
Journal Article
Open access
PDF file
Shinichiro AdachiShinichiro Adachi
Shinichiro Adachi
NUNobuhiro Ueda
Nobuhiro Ueda
Cold-spray techniques have been a significant development for depositing metal coatings in recent years. In cold-spray processes, inexpensive nitrogen gas is widely used as the propellant gas in many industries. However, it is difficult to produce austenitic stainless steel coatings with dense microstructures with cold-spray techniques when using nitrogen propellant gas because of work hardening. In this study, the effects of cold-spray conditions using a nitrogen propellant gas on AISI 316L stainless steel coatings were examined. It was found that a higher nitrogen propellant gas temperature and pressure produce coatings with dense microstructures. The measured AISI 316L coating hardness values suggest that AISI 316L particles sprayed at temperatures of 700 and 800 °C soften due to the heat, allowing uniform deformation on the substrate and consequently forming dense coating microstructures. In addition, AISI 316L powder with particle diameters of 5–20 µm resulted in a denser coating microstructure than powder with particle diameters of 10–45 and 20–53 µm. Finally, the standoff distance between the nozzle and the substrate also affected the AISI 316L coating microstructures; a standoff distance of 40 mm produced the densest microstructure.

1 September 2013 in Advanced Powder Technology
Verified
Journal Article
Closed access
Shinichiro AdachiShinichiro Adachi
Shinichiro Adachi
NUNobuhiro Ueda
Nobuhiro Ueda

1 November 2012 in Thin Solid Films
Verified
Journal Article
Closed access
Shinichiro AdachiShinichiro Adachi
Shinichiro Adachi
NUNobuhiro Ueda
Nobuhiro Ueda

1 November 2014 in Surface and Coatings Technology
Verified
Journal Article
Closed access
Shinichiro AdachiShinichiro Adachi
Shinichiro Adachi
NUNobuhiro Ueda
Nobuhiro Ueda

10 December 2018 in Coatings
Verified
Journal Article
Open access
PDF file
Shinichiro AdachiShinichiro Adachi
Shinichiro Adachi
NUNobuhiro Ueda
Nobuhiro Ueda
Cold-sprayed AISI 316L stainless steel coatings are treated to form an austenite phase with excessive dissolved nitrogen (known as the S-phase) by plasma nitriding at temperatures below 450 °C. The S-phase is a hard and wear-resistant layer with high corrosion resistance. However, the S-phase layer formed after only nitriding is thin and the hardness abruptly decreases at a certain depth; it lacks mechanical reliability. We examined two types of combined low-temperature plasma treatment to enhance the mechanical reliability of the S-phase layer: (i) sequential and (ii) simultaneous. In the sequential plasma treatment, the carburizing step was followed by nitriding. In the simultaneous treatment, the nitriding and carburizing steps were conducted at the same time. Both combined plasma treatments succeeded in thickening the S-phase layers and changed the hardness depth profiles to decrease smoothly. In addition, anodic polarization measurements indicated that sequential treatment involving carburizing followed by nitriding for 2 h each resulted in high corrosion resistance.