In this paper, we demonstrate, for the first time, an isolating bandpass filter with low-loss forward transmission and high reverse isolation by modulating its constituent resonators. To understand the operating principle behind the device, we develop a spectral domain analysis method and show that the same-frequency nonreciprocity is a result of the nonreciprocal frequency conversion to the intermodulation (IM) frequencies by the time-varying resonators. With appropriate modulation frequency, modulation depth, and phase delay, the signal power at the IM frequencies is converted back to the RF frequency and adds up constructively to form a low-loss forward passband, whereas they add up destructively in the reverse direction to create the isolation. To validate the theory, a lumped-element three-pole 0.04-dB ripple isolating filter with a center frequency of 200 MHz and a ripple bandwidth of 30 MHz is designed, simulated, and measured. When modulated with a sinusoidal frequency of 30 MHz, a modulation index of 0.25, and an incremental phase difference of 45°, the filter achieves a forward insertion loss of 1.5 dB and a reverse isolation of 20 dB. The measured nonmodulated and modulated results agree very well with the simulations. Such nonreciprocal filters may find applications in wideband simultaneous transmit and receive radio front ends.

RF fingerprinting is an emerging technology for identifying hardware‐specific features of wireless transmitters and may find important applications in wireless security. In this study, the authors present a new RF fingerprinting scheme using deep neural networks. In particular, a long short‐term memory based recurrent neural network is proposed and used for automatically identifying hardware‐specific features and classifying transmitters. Experimental studies using identical RF transmitters showed very high detection accuracy in the presence of strong noise (signal‐to‐noise ratio as low as dB) and demonstrated the effectiveness of the proposed scheme.

In this article, we present the first demonstration of distributed and symmetrical all-band quasi-absorptive filters that can be designed to arbitrarily high orders. The proposed quasi-absorptive filter consists of a bandpass section (reflective-type coupled-line filter) and absorptive sections (a matched resistor in series with a shorted quarter-wavelength transmission line). Through a detailed analysis, we show that the absorptive sections not only eliminate out-of-band reflections but also determine the passband bandwidth (BW). As such, the bandpass section mainly determines the out-of-band roll-off and the order of the filter can be arbitrarily increased without affecting the filter BW by cascading more bandpass sections. A set of 2.45-GHz one-, two-, and three-pole quasi-absorptive microstrip bandpass filters are designed and measured. The filters show simultaneous input and output absorption across both the passband and the stopband. Measurement results agree very well with the simulation and validate the proposed design concept.

Simultaneous multitarget vital signs measurement has become a hot issue for noncontact vital signs perception. However, there is still challenge in the multitarget heartbeat measurement due to the weakness of heartbeat signal and interference from complex environment. In this article, a new multiple-input–multiple-output (MIMO) continuous-wave (CW) radar system equipped with 2-D digital beamforming (DBF) is presented to measure the respiration and heartbeat of multiple human subjects at unknown positions simultaneously. Through 2-D beam scanning of the whole scene, a 2-D radar image is generated. From the image, the chest motion of multiple targets is accurately located. Then, the vital signs of targets are obtained through forming individual beams focusing on the chests of targets. Moreover, the low intermediate frequency (low-IF) architecture is adopted to minimize the impact of flicker noise in low-frequency amplifier stages. The experimental results demonstrate that the proposed MIMO 2-D imaging radar system can locate chest areas of multiple targets, suppress the clutters, and make vital signs measurement, heartbeat measurement in particular, more robust compared with single-input–multiple-output (SIMO) radar system in complex environment.

This paper presents for the first time the design, fabrication, and demonstration of a dielectric waveguide (DWG)-based ortho-mode sub-THz interconnect channel for planar chip-to-chip communications. By combining the proposed new transition of microstrip line with DWG orthogonally, the ortho-mode transition is constructed to form an ortho-mode channel. The measured minimum insertion losses for the Ey₁₁ mode and the Ex₁₁ mode are 6.6 dB with 20.3-GHz 3-dB bandwidth and 6.5 dB with 55.2-GHz 3-dB bandwidth, respectively. The simulation and measurement results agree well with each other.