Emidio DiGiampaolo

Prof. Dr. Emidio DiGiampaolo

orcid

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 February 2013 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
EDEmidio DiGiampaolo
Emidio DiGiampaolo
FMFrancesco Martinelli
Francesco Martinelli
This paper presents a global localization system for an indoor autonomous vehicle equipped with odometry sensors and a radio-frequency identification (RFID) reader to interrogate tags located on the ceiling of the environment. The RFID reader can measure the phase of the signals coming from responding tags. This phase has non-univocal dependence on the distance robot tag, but in the considered frequency, it is really sensitive to a change in the position of the robot. For this reason, a multihypothesis Kalman filtering approach provides a really satisfactory performance even in the case that a very small density of tags is used: In the experimental tests, an average position estimation error of about 4 cm is achieved using only two tags for an area of about 5 m2.

20 October 2011 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
EDEmidio DiGiampaolo
Emidio DiGiampaolo
FMFrancesco Martinelli
Francesco Martinelli
A global localization system combining odometry data with radio frequency identification (RFID) readings is proposed. RFID tags are placed at the ceiling of the environment and can be detected by a mobile robot unit traveling below them. The detection of the tags is the only information used in the proposed approach (no distance or bearing to the tag is considered available), but differently from similar localization setups reported in the literature, only a small number (about one each square meter or less) of tags are used. This is possible using a suitable tag's antenna in ultrahigh frequency band, expressly designed to obtain regular and stable RFID detection regions, which allows us to consider an efficient Kalman filtering approach to fuse RFID readings with the vehicle odometry data. A satisfactory performance is achieved, with an average position error of about 0.1 m. The hardware/software localization setup described in this paper is cheap and easy to use and may provide a satisfactory approach in several industrial and domestic scenarios.

1 December 2009 in IEEE Antennas and Propagation Magazine
Verified
Journal Article
Closed access
GMGaetano Marrocco
Gaetano Marrocco
EDEmidio DiGiampaolo
Emidio DiGiampaolo
RAR. Aliberti
R. Aliberti
The reading range is one of the most critical performance indicators of radio-frequency identification (RFID) systems. It depends on many physical and geometrical parameters. Typically, in the ultra-high-frequency band (UHF: 860 MHz to 960 MHz), the maximum size of the reading region is estimated by the free-space propagation model. This is based on the Friis formula, even if much more accurate predictions may be accomplished nowadays by time-consuming electromagnetic simulations, accounting for the antennas and the interaction with the nearby environment. This paper proposes a general parameterization of the three-dimensional reading region. This done having introduced all of the accessible system data, such as the emitted power, the reader and tag-over-object radiation patterns, and also the interrogation duty cycle, the scenario features, and the safety regulation constraints. Within this framework, the opportunity and some improvements of the free-space model are analyzed. They are compared with measurements and with more-accurate three-dimensional simulations of realistic environments. The discussion demonstrates the validity range of the free-space approximations, and evaluates the improvement achieved by including the main interactions with the environment. The derived formulas are ready to use and to be applied for the planning and optimization of reader-tag networks.

26 September 2014 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
SCStefano Caizzone
Stefano Caizzone
EDEmidio DiGiampaolo
Emidio DiGiampaolo
GMGaetano Marrocco
Gaetano Marrocco
The possibility to wirelessly monitor the state and the evolution of cracks is of increasing interest in emerging structural health monitoring systems. A simple and effective measurement method considers the placement of two passive radio frequency identification (RFID) antennas on top of the crack, so that the crack's evolution will produce a change of the inter-antenna coupling and in turn of the phase of the backscattered field. An ad-hoc design technique, based onto the coupled-modes physics, permits to maximize the sensor's sensitivity avoiding, or at least mitigating, the read range reduction during the evolution of the displacement that is instead typical of amplitude-oriented RFID displacement sensors. The proposed idea is demonstrated by numerical and experimental examples showing the possibility of sub-millimeter resolution with low-cost devices.

13 August 2018 in IEEE Sensors Journal
Verified
Journal Article
Closed access
EDEmidio DiGiampaolo
Emidio DiGiampaolo
FMFrancesco Martinelli
Francesco Martinelli
This paper faces the problem of a robot that patrols a warehouse and localizes objects on shelves using RFID technology. A two-step localization system has been developed. First, the robot localizes itself by means of a Kalman-based algorithm that fuses robot odometry with the information coming from the phase of the signals of few reference RFID tags deployed along the shelves. Then, the objects on the shelves are localized using an algorithm that matches the phase of the signals from tagged objects collected along specific paths (suitably devised to decouple the estimation problem of the different tag coordinates) with a parametric electromagnetic model. A numerical analysis has been reported to show that the estimation error in the tag coordinates remains in the order of a few centimeters under several operating conditions of the system (e.g., for different values of the standard deviation of the measurement noise or under several parameter perturbations). Experimental tests in real scenarios assess the effectiveness of the system: the average position estimation error of the objects is about 10 cm in the case of cluttered metallic shelves but decreases up to a few centimeters in the case of stacked cartons.

21 November 2016 in IEEE Sensors Journal
Verified
Journal Article
Closed access
EDEmidio DiGiampaolo
Emidio DiGiampaolo
ADAlessandro DiCarlofelice
Alessandro DiCarlofelice
AGAmedeo Gregori
Amedeo Gregori
Strain gauge measurements are widely used in structural health monitoring and damage detection of existing infrastructures as well as in laboratory prototyping tests of new structures and materials. Wireless sensing of strain gauge is desirable in many practical applications because of the difficulty to access at the measurement point or to handle wired sensors. In this paper, we show a semi-passive wireless strain gauge sensor, which allows a high level of measurement accuracy comparable with that of wired strain sensors. It overcomes the limits and drawbacks of devices based on wireless sensor networks and those based on similar RFID-based sensors. The ability to perform measurements over long distances and to handle fast time-varying phenomena (e.g., vibration) makes the proposed device practical in realistic scenarios.