In this paper, to save energy and reduce consumption in building ceramic process, the low temperature porcelain building tiles were prepared by fast firing process using two kinds of “K2O–Na2O” feldspar with different amounts of alkaline and alkaline earth oxides fluxing agents, Si/Al ratio and melting point. The sintering properties of the samples were evaluated by linear shrinkage, water absorption and bulk density. The crystalline phase and microstructure of the samples were characterized by X-ray diffraction and scanning electron microscope. The results showed that the optimum linear shrinkage of 7.55%, water absorption of 0.03% and bending strength of 78.3–85.8 MPa can be achieved for the sample fired at 1170–1190°C, which is attributed to the effect of the combined “K2O–Na2O” feldspar flux system.
22 October 2022 in Materials Chemistry and Physics
The mullite columnar structure are prepared by a dry-press method using waste gangue substituted for kaolin clay. The properties e.g., water absorption, bulk density and bending strength of the samples fired at the temperature range of 13001550°C are studied. The microstructure of mullite columnar structures are characterized by X-ray diffraction and field emission scanning electron microscopy with an energy dispersive X-ray spectroscopy. The results reveal that waste gangue substituted for the kaolin is available for mullite columnar structure. Impurities in waste gangue e.g., TiO 2 and Fe 2 O 3 lower the formation temperature of mullite columnar structure, which endow the samples with high refractoriness. Due to the presence of interlocking structure constructed by mullite crystals, the sample achieves the optimum bending strength of 97.6 MPa at the temperature of 1400°C, which is future application in refractory materials. The dry-pressed preparation method provides a simple way to synthesize mullite columnar structure using waste gangue substituted for kaolin clay that can be future applied in lightweight refractory industry.
1 January 2017 in Journal of the Ceramic Society of Japan
Cr-doped calcium titanate (CaTiO 3) pigments with prism-like shape were synthesized by a simple solvothermal process without any surfactants. The colouring mechanism and performance of Cr-doped CaTiO 3 yellow pigment samples were investigated by X-ray diffraction, diffuse reflection spectroscopy, field scanning electron microscopy and colorimeter. When Cr-doping concentrations were 0.010.05% (mole fraction, the same below), solid solution formed so that the yellow pigments would have a CaTiO 3 phase composition. The intensity of the yellow colour in the pigment samples was related to the presence of Cr ions. The optimum yellow pigment was achieved when the Cr-doping concentration was 0.03% mol. At a high temperature of 1280°C, Cr-doped CaTiO 3 yellow sample provided a stronger and more intense colour as Cr ions dissolved into the stable CaTiO 3 structure. This solvothermal preparation method provides a simpler way to synthesize a more colourful ceramic pigment that can be applied in ceramic decoration or inkjet printers.
1 October 2020 in Journal of the Ceramic Society of Japan
The “K2O–Na2O” binary and “K2O–Na2O–Li2O” ternary flux systems on the densification behaviors of the porcelain building ceramic were analyzed. The results showed that when K2O and Na2O content were equivalently replaced by Li2O content, the sintering temperature of “K2O–Na2O–Li2O” flux samples was reduced to 1090–1130 °C, which is lower than that of “K2O–Na2O” binary flux sample (1130–1160 °C). The corresponding sintering temperature range of the ternary flux sample is widened from 30 to 40 °C, and thus the bending strength of the ternary flux sample is increased by 3.5 %. energy spectrometer system and “K2O–Na2O–Li2O” ternary frit simulation results indicate ternary flux sample has more Al2O3 and SiO2 content in glass phase than those of the binary flux sample, however, the alkaline oxide contents are higher than those of ternary flux sample. For binary flux samples, “K2O–Na2O” fluxes melt themselves due to low melting point and thus suddenly appear a large amount of the liquid phase and have no time to dissolve Al2O3 and SiO2 contents, resulting in low glassy viscosity of the sample. However, when Li2O content equivalently replace K2O and Na2O contents for the ternary flux sample, they would appear high glassy viscosity steeply, due to the formation of low eutectic mixture melted with high Al2O3 and SiO2 contents. Combined with X-ray powder diffraction patterns and scanning electron microscope images, the ternary flux samples have more crystallite phase, smaller porosity and pore size than those of binary flux samples. Therefore, the properties of the ternary flux samples are superior to those of binary flux samples.