This paper deals with a low to middle order finite volume/lumped capacitance thermal model of an electric machine and the correction of critical parameters. The different parts of the electric machine are divided into sub-volumes called finite volumes or lumped capacitances. From the given characteristic geometry of the electric machine, the thermal resistances to create the system matrix are calculated. The resulting non-linear equation system is solved for steady state condition for a given current density. The result is compared to experimental measurements allowing the calculation of material correction parameters included in the thermal resistances using the least square method. In a second step an experiment with time dependent current in the stator windings is done. The experiment then is simulated with the time dependent current measured in the experiment using the correction parameters found in the first step. The paper aims to present the possibility to calculate the maximum temperatures very accurately with this method.
As an extension of a paper published at the 24th International Conference on Mechatronics Technology, ICMT 2021 conference, this paper shows the concept, design method, and model of a hybrid brake with additional validation. An eddy current brake cannot be used to decelerate a vehicle to a standstill. However, the magnetic attraction force between the rotor and stator of an eddy current brake can be used to generate an additional mechanical friction torque. By using a disc spring between the rotor and stator, the eddy current brake is extended to a so-called hybrid brake. In particular, the model and design method of the disc spring are the focus of this work. Using a system model that includes the electromagnetic and mechanical domains, the wear reduction compared to a conventional friction brake and the dynamic behaviour depending on the spring parameters are investigated. Finally, a disc spring is designed in FEM with the desired force–displacement curve. In addition, a working demonstrator of a hybrid brake is constructed, and the electromagnetic and mechanical system models are compared with the experimental results. For the first time, it is shown that the concept of using the magnetic attraction force between the rotor and stator of an eddy current brake for braking to a stop is working. In a speed range of 0–7500 rpm, it is possible to generate a torque of 100 Nm, whereby at speeds higher than 3500 rpm, the torque is generated in a wear-free manner by eddy currents. However, in order to be valid, the model must be extended to represent the deformation of the rotor.
This work presents a thermal modeling approach for evaluating the maximum allowable excitation current in an electrically excited eddy current brake (ECB) integrated into electric vehicle drivetrains. Designed to meet UNECE Regulation No. 13 requirements, the model enables safe operation by predicting temperature development within the excitation windings and rotor. A lumped parameter thermal model (LPTM) is formulated using Biot number analysis to guide geometric simplification and ensure computational efficiency. The model accounts for anisotropic thermal properties, insulation effects, and worst-case boundary conditions. Validation is performed through thermal measurements on a physical rotor and comparison with a high-fidelity FEM simulation. Results confirm the model's accuracy and suitability for design optimization under thermal constraints.
Die Diagnostik von Krankheiten der Augenlider, Orbita und Tränenwege gehören zum Alltag der ophthalmologischen Versorgung. Die Krankheitsbilder sind vielfältig und ihre Diagnose erfordert meist mehrere diagnostische Schritte. Hierbei sind die klinische Untersuchung und die Erhebung eines sog. „Adnexen-Status“ besonders wichtig. Die folgenden Seiten sollen eine systematische Übersicht und strukturierte Herangehensweise bieten.
Electrically excited eddy current brakes (ECBs) with solid active material suffer from low power density due to non-uniform heat dissipation caused by the skin effect. This paper presents an anisotropic material structure consisting of flux-conducting steel pins surrounded by electrically conductive perforated sheets, which simultaneously reduces the skin effect and enables direct liquid cooling of the active material. Two structural variants are investigated: a PIN structure with cylindrical flux-conducting elements and a cluster structure with elements in a hexagonal cluster configuration. A computationally efficient 2D reluctance network model is developed for both variants, combining analytically derived reluctances with FEM pre-computed reluctances for air spaces and frequency-dependent reluctances of the flux-conducting elements. The model is validated against measured torque characteristics of two experimental demonstrators over the full range of excitation currents from 10 to 80 A. Good agreement between simulation and measurement is achieved after correcting for two systematic deviations identified during validation: a geometric effect at the inner and outer edges of the perforated sheets that reduces the effective eddy current path resistance, and the temperature dependence of the sheet resistance. The critical rotational speed is accurately reproduced by the corrected model. The uncertainty range due to undetermined thermal operating conditions is quantified, providing a reliable basis for the design and optimization of ECBs with anisotropic material structure. Quantitative error analysis shows that the corrections reduce the root mean square error for the cluster structure by up to 77%, yielding a maximum error below 10% across the 50–100% excitation-current range. For the PIN structure, in contrast, a residual deviation of up to 15% remains at maximum excitation current, attributed to uncertainty in the magnetization curve of the flux-conducting elements. The model requires fewer than 100 degrees of freedom and computes a full torque–speed characteristic in under 5 min, four to five orders of magnitude faster than a full 3D transient FEM simulation. The uncertainty range due to undetermined thermal operating conditions is quantified, providing a reliable basis for the design and optimization of ECBs with anisotropic material structure.