Floating offshore wind turbines have the potential to commercially convert the vast wind resource in deep-water area. Compared with fixed-bottom wind turbines, motions of the floating foundation complicate vibrations and loads of the wind turbine in offshore environment. To alleviate the responses of the wind turbine, this study investigates the use of fore–aft tuned mass damper (TMD) in nacelle/tower for passive control of a semi-submersible offshore wind turbine. A simplified structural model, considering the degree-of-freedom of platform pitch and surge, tower tilt and TMD translation, is proposed in the light of motion features of semi-submersible platform. After identifying ten unknown parameters, the correctness of the deterministic model is validated by pitch free decay responses. The mass, stiffness and damping of TMD are optimized using both method of exhaustion and genetic algorithm to avoid local minimum. Six optimized TMD devices are evaluated under three kinds of realistic environment conditions. The control effectiveness is assessed by the extreme and fatigue response reduction ratios. It is found that the high stiffness TMDs that directly dissipate the energy of tower oscillation exhibit an overall stable performance. Similar to the spar-type foundation, the TMDs in the nacelle/tower are capable of extending the service life of floating wind turbines.

A preliminary study is carried out to investigate the aerodynamic characteristics of a square cylinder with Savonius wind turbines and to explain the reason why this kind of structure can suppress wind-induced vibrations. A series of computational fluid dynamics simulations are performed for the square cylinders with stationary and rotating wind turbines at the cylinder corners. The turbine orientation and the turbine rotation speed are two key factors that affect aerodynamic characteristics of the cylinder for the stationary and rotating turbine cases, respectively. The numerical simulation results show that the presence of either the stationary or rotating wind turbines has a significant effect on wind forces acting on the square cylinder. For the stationary wind turbine cases, the mean drag and fluctuating lift coefficients decrease by 37.7% and 90.7%, respectively, when the turbine orientation angle is 45°. For the rotating wind turbine cases, the mean drag and fluctuating lift coefficients decrease by 34.2% and 86.0%, respectively, when the rotation speed is 0.2 times of vortex shedding frequency. Wind turbines installed at the corners of the square cylinder not only enhance structural safety but also exploit wind energy simultaneously.

The Y-shape (triangular) semi-submersible foundation has been adopted by most of the built full-scale floating wind turbines, such as Windfloat, Fukushima Mirai and Shimpuu. Considering the non-fully-symmetrical shape and met-ocean condition, the foundation laying angle relative to wind/wave directions will not only influence the downtime and power efficiency of the floating turbine, but also the strength and fatigue safety of the whole structure. However, the dynamic responses induced by various aligned wind and wave load directions have scarcely been investigated comparatively before. In our study, the directionality effects are investigated by means of combined wind and wave tests and coupled multi-body simulations. By comparing the measured data in three load directions, it is found that the differences of platform motions are mainly derived from the wave loads and larger pitch motion can always be observed in one of the directions. To make certain the mechanism underlying the observed phenomena, a coupled multi-body dynamic model of the floating wind turbine is established and validated. The numerical results demonstrate that the second-order hydrodynamic forces contribute greatly to the directionality distinctions for surge and pitch, and the first-order hydrodynamic forces determine the variations of tower base bending moments and nacelle accelerations. These findings indicate the directionality effects should be predetermined comprehensively before installation at sea, which is important for the operation and maintenance of the Y-shape floating wind turbines.

This paper investigates the effect of fitting fins at the corners of a square cylinder on aerodynamic characteristics of the cylinder via wind tunnel tests and large eddy simulations (LES). Although it has been recognized that the corner fins have a remarkable effect on aerodynamic characteristics of a square cylinder, no study has been carried out to systematically evaluate this effect and reveal the underlying mechanism. Three types of corner fin configurations, i.e. fins fitted only to the leading corners, fins fitted only to the trailing corners, and fins fitted to both leading and trailing corners were studied. It was found that the corner fins significantly influence aerodynamic characteristics, such as mean drag coefficient, fluctuating lift coefficient, and vortex shedding of the cylinder. The influences of these corner fin configurations are very different. In general, the leading and trailing fins have an opposite effect on these characteristics. The mechanisms underlying these effects were clarified based on the flow regime visualized via LES. The interesting findings have practical significances not only for reducing aerodynamic forces and wind-induced vibration of infrastructures, but also for enhancing wind-induced vibration-based energy harvesting.