Currently, cannabis is considered an attractive option for the treatment of various diseases, including pain management. Thus, developing new analgesics is paramount for improving the health of people suffering from chronic pain. Safer natural derivatives such as cannabidiol (CBD) have shown excellent potential for the treatment of these diseases. This study aimed to evaluate the analgesic effect of a CBD-rich cannabis extract (CE) encapsulated in polymeric micelles (CBD/PMs) using different pain models. The PEG-PCL polymers were characterized by gel permeation chromatography and ¹H-NMR spectroscopy. PMs were prepared by solvent evaporation and characterized by dynamic light scattering (DLS) and transmission electron microscopy. The analgesic activity of CBD/PMs and nonencapsulated CE rich in CBD (CE/CBD) was evaluated using mouse thermal, chemical, and mechanical pain models. The acute toxicity of the encapsulated CE was determined by oral administration in mice at a dose of 20 mg/kg for 14 days. The release of CBD from the nanoparticles was assessed in vitro using a dialysis experiment. CBD/PMs with an average hydrodynamic diameter of 63.8 nm obtained from a biocompatible polyethylene glycol-block-polycaprolactone copolymer were used as nanocarriers for the extract formulations with 9.2% CBD content, which corresponded with a high encapsulation efficiency of 99.9%. The results of the pharmacological assays indicated that orally administered CBD/PMs were safe and exerted a better analgesic effect than CE/CBD. The micelle formulation had a significant analgesic effect in a chemical pain model, reaching a percentage of analgesia of 42%. CE was successfully encapsulated in a nanocarrier, providing better stability. Moreover, it proved to be more efficient as a carrier for CBD release. The analgesic activity of CBD/PMs was higher than that of free CE, implying that encapsulation is an efficient strategy for improving stability and functionality. In conclusion, CBD/PMs could be promising therapeutics for pain management in the future.

The possibility of using an electrochemical biosensor, using screen-printed electrodes modified with a carbonaceous material and a commercial kit for the determination of glucose, to monitor an ethanolic fermentation was analyzed. The determination is based on the electrochemical oxidation reaction of NADH that occurs at a potential where the components of the kit do not generate a current signal, even in the presence of the fermentation medium. The electrochemical system was used to analyze the variation of glucose concentration during a laboratory-scale fermentation. The results were contrasted with the variation of standard characterization parameters such as pH, total soluble solids (TSS), the viability of the yeast, and concentration of ethanol produced. Of these values, the total soluble solids should be related to the concentration of glucose obtained by the electrochemical sensor, however, this last measure is more specific for sugar since the TSS refers to all soluble solids. The obtained results allow us to verify the usefulness of the electrochemical method for real-time monitoring of a fermentation.

The electrochemical behavior of Saccharomyces cerevisiae sp was studied using a glassy carbon electrode (GCE) modified with Nafion-dispersed oxidized multi-walled carbon nanotubes (OMWCNT). The morphology was studied using scanning electron microscopy (SEM), showing that the yeast sticks to the carbon nanotube surface instead of the glassy carbon surface. The redox couple Fe(CN)₆⁴⁻/Fe(CN)₆³⁻ was used to determine the electroactive area and the heterogeneous transfer constant, which increased 80.5% and 108% respectively by the presence of nanotubes. The studies of the pH effect showed that the anodic potential decreases at alkaline pH and that the highest current intensity occurs at a pH value of 7.00. Studies of the scan rate effect have shown that yeast oxidation is an irreversible mixed control process in which two electrons participate. The relationship between yeast concentration and the anodic current density was studied using different electrochemical techniques obtaining the best analytical parameters through chronoamperometry. The linear range was between 3.36 and 6.52 g L⁻¹, the limit of detection (LOD) and the limit of quantification (LOQ) were 0.98 g L⁻¹ and 3.36 g L⁻¹ respectively, and the sensibility obtained was 0.086 μA L g⁻¹ mm⁻². These results show that the multi-walled carbon nanotubes in water and Nafion® allow obtaining an anodic signal corresponding to the yeast, which facilitates its quantification through electrochemical methodologies, favoring the reduction of analysis times and costs compared with other techniques.

The potential of king grass biomass as a precursor for carbon-based materials was evaluated through comprehensive physicochemical characterization. The biomass showed high fixed carbon content, reactive oxygenated groups, and favorable atomic ratios, supporting its suitability for conversion into porous carbon structures. This study focused on the synthesis of graphene-like materials via high-temperature pyrolysis (~1000 °C), employing FeCl₃ and potassium ferricyanide (K₃[Fe(CN)₆]) as catalytic agents. Although FeCl₃ is widely studied, it showed limited capacity to promote graphitic ordering. In contrast, K₃[Fe(CN)₆] exhibited a synergistic effect, combining iron-based catalytic species (Fe, Fe₃C) and potassium-derived activating compounds (K₂CO₃), which significantly enhanced graphitization and porosity. Characterization by Raman spectroscopy, XRD, and SEM confirmed that materials synthesized with K₃[Fe(CN)₆] presented improved crystallinity, lower defect densities (I_D/I_G = 0.37–1.11), and distinct 2D bands (I_2D/I_G = 0.32–0.80), indicating the formation of few-layer graphene domains. The most promising structure was obtained from cellulose treated with alkaline peroxide and deoxygenated prior to pyrolysis with K₃[Fe(CN)₆], showing properties comparable to commercial graphene. BET analysis revealed surface areas up to 714.50 m²/g. While non-catalyzed samples yielded higher mass, the catalytic approach with K₃[Fe(CN)₆] demonstrates a sustainable and efficient pathway for producing graphene-like carbon materials from lignocellulosic biomass.