Using gangue backfilling in underground coal mining not only controls the roof deformation in the gob area but also reduces the amount of mining waste rock. However, due to the limitations of the complicated engineering conditions, backfilling mining in the steep coal seam is not widely applied. In this study, a long-distance backfilling technology with a scraper winch for a steep coal seam was proposed and applied in a flexible shield supporting working face in Datai Mine, Beijing. Aiming at the problem of the decreasing backfilling ratio in field practice, numerical simulation was carried out to research the moving law of gangue in the goaf. The gangue mainly experienced four stages: gangue landslide stage, small-scale subsidence stage, funnel-shaped subsidence stage, and large-scale subsidence stage. The moving area of the gangue could be divided into five areas including a motionless area, a landslide area, a subsidence area, a funnel-shaped subsidence area, and a to-be-backfilled area. With the increase of the inclined length of the working face, the moving time of the gangue increased gradually. Based on the simulation results, the scheme of backfilling and mining in Datai Mine was optimized, for which the inclined length of the working face was shortened, and a higher backfilling ratio was obtained.

Waste-rock material used in underground backfill mining has a granular texture and acquires non-linear deformation characteristics when compressed. The deformation modulus of waste-rock measured by a laboratory compression test is significantly different from the true deformation modulus in the field, due to the complete confining effect of the loading steel cylinder. In this study, we performed a series of laboratory-based compression tests on waste-rock samples. The results showed that lab-acquired deformation modulus variations of waste rock could be divided into three stages: slow increase, accelerated increase, and rapid increase. We also measured the true deformation modulus of backfill waste rock by conducting a field test in gob areas of the Tangshan coal mine, China. The hardening process of backfill waste rock during the field test was analyzed, and could be divided into four stages: roof contact, rapid compression, slow compression, and long-term stable. With the increase of axial strain, the lab- and field-measured deformation moduli of waste rock both increased exponentially. A correction parameter was proposed to investigate the relationship between the field-generated true deformation modulus and the lab-tested deformation modulus. The correction parameter k positively correlated with the axial strain, in the form of an exponential function. The magnitude of k was between 0.5616 and 0.6531.

The deformation and failure of a coal–rock system in a deep environment is affected by its own mechanical properties, natural endowments, and geological structures; it is very important to study the energy evolution law of coal–rock systems. For this purpose, a Particle Flow Code in 2 Dimensions (PFC2D) simulation was conducted to assess the coal–rock structure and roadway surrounding rock. The hard roof would produce a rebound “energy supply” phenomenon when the coal was destroyed, and the influence of rock strength on the energy evolution of the coal–rock combination was analyzed. In addition, the energy evolution law of roadway surrounding rock with different roof strength is studied; the energy evolution process of roof and coal seam and deep and shallow coal mass are compared, according to the energy storage characteristics of roadway surrounding rock in different areas; the partition energy storage model of roadway surrounding rock is established preliminarily and the concepts of energy storage area and energy supply area of roadway surrounding rock are proposed; the prevention and control methods of near-field rock burst in deep roadways are discussed, and the research conclusions can provide theoretical reference for the research on the mechanism of rock burst in deep coal mines.

Destress drilling method is one of the commonly used methods for mitigating rock bursts, especially in coal mining. To better understand the influences of drilling arrangements on the destress effect is beneficial for rock burst mitigation. This study first introduced the rock burst mitigation mechanism of the destress drilling method and then numerically investigated the influences of drilling arrangements on the mechanical properties of coal models through uniaxial compression tests. Based on the test results, the energy evolution (i.e., the energy dissipation and bursting energy indexes) influenced by different drilling arrangements was analyzed. When the drilling diameter, the number of drilling holes in one row, or the number of drilling rows increases, the bearing capacity of specimens nonlinearly decreases, but the energy dissipation index increases. In addition, the drilling diameter or the number of drilling holes in one row affects the failure mode weakly, which is different from that of the number of drilling rows. Consequently, the bursting energy index decreases as increasing the drilling diameter or the number of drilling holes in one row, but as increasing the number of drilling rows, the variation law of bursting energy index is not obvious. At last, the influencing mechanism of drilling arrangement on the rock burst prevention mechanism of the destress drilling method was discussed and revealed.

Backfill mining is an effective option to mitigate ground subsidence, especially for mining under surface infrastructure, such as buildings, dams, rivers and railways. To evaluate its performance, continual long-term field monitoring of the deformation of backfilled gob is important to satisfy strict public scrutiny. Based on industrial Ethernet, a real-time monitoring system was established to monitor the deformation of waste-rock-backfilled gob at −700 m depth in the Tangshan coal mine, Hebei Province, China. The designed deformation sensors, based on a resistance transducer mechanism, were placed vertically between the roof and floor. Stress sensors were installed above square steel plates that were anchored to the floor strata. Meanwhile, data cables were protected by steel tubes in case of damage. The developed system continually harvested field data for three months. The results show that industrial Ethernet technology can be reliably used for long-term data transmission in complicated underground mining conditions. The monitoring reveals that the roof subsidence of the backfilled gob area can be categorized into four phases. The bearing load of the backfill developed gradually and simultaneously with the deformation of the roof strata, and started to be almost invariable when the mining face passed 97 m.

Research on energy accumulation and releasing in the rock plays a key role on revealing its failure mechanism. This paper establishes a microscopic structure model of granite using Otsu digital image processing (DIP) technology and particle flow code software (PFC2D). A series of numerical compression tests under different confining pressures were conducted to investigate the macro and micro characteristics of energy evolution in granite. The results showed that the energy evolution of granite is divided into three stages: stable accumulation, slow dissipation, and rapid release. With increasing confining pressure, the strain energy accumulation ratio decreased exponentially and the peak value of strain energy increased linearly. It was found that the energy accumulation speed in the pre-peak stage increased as a linear function, while the energy release speed in the post-peak stage decreased as an exponential function. In addition, the feldspar is the main microstructure which played a major part in accumulating energy in granite. However, the unit mineral energy of mica particles was bigger than that of feldspar and quartz. When subjected to increasing confining pressure, the feldspar’s total energy growth rate was fastest. Meanwhile, the mica’s unit energy growth rate was fastest.