This paper presents an experimental investigation on pressure distribution on human foot and balancing characteristics on human foot health. Feet are the parts of the human body that will sustain the highest pressure during standing. Analysis of foot plantar pressure distributions helps in revealing the interface pressure between the foot plantar surface and the shoe sole. The objectives of this research are to study on behavioural of the human foot pressure distribution and balancing during standing. In this study, five factors are considered for the experiment to establish the behavioural of humans’ foot, which are body mass index, gender, type of arch, diabetic and progressive foot deformity. Therefore, the experiment is conducted in order to know the pressure distribution based on factors by using Force Resistive Sensor. As a result, foot pressure distribution for normal subjects usually concentrated on the forefoot, followed by hind foot and middle foot. Body mass index also affects the pressure distribution as an increase in pressure follows an increase in body mass index and vice versa. As for gender factor, there is no significant difference in the pattern of pressure distribution between males and females. While for the type of feet arch factor, the different arch will give different locations of peak pressure. The diabetic factor, pressures will distribute more to the metatarsals and heel area while for progressive foot deformity factor, the pressure is usually distributed at the metatarsals and the toe area.
In monopropellant system, hydrogen peroxide is used with catalyst to create an exothermic reaction. Catalyst made of silver among the popular choice for this application. Since the catalyst used is in porous state, the effect of its porosity in the hydrogen peroxide monopropellant thruster performances is yet unknown. The porosity changes depending on factors including catalyst pact compaction pressure, bed dimension, and type of catalyst used. As researches on this topic is relatively small, the optimum porosity value is usually left out. The performance of the thruster indicated by the pressure drop across the catalyst bed. Porosity of the catalyst bed adds additional momentum sink to the momentum equation that contributes to the pressure gradient which lead to pressure loss inside thruster. The effect of porosity influences the performance and precision of the thruster. Study of the pressure drop by the catalyst bed requires a lengthy period and expensive experiments, however, numerical simulation by mean of Computational Fluid Dynamics (CFD) can be an alternative. In this paper, 90 wt% hydrogen peroxide solution with silver catalyst is studied in order to investigate the influence of porosity to the performances of the thruster, and to find the optimum porosity of the thruster. Species transport model is applied in the single-phase reaction simulation using the EDM for turbulence-chemistry interaction. Through this study, the effect of porosity towards the thruster performances represented in term of pressure drop, exit velocity, bed temperature, and thrust, and porosity of 0.4 found to be as an optimal value.
Fuel in transportation is necessary and gas release from transportation activity raises concern of pollution. Sustainable fuels sources are from biomass can convert to the alternative to the bioenergy fuel. It is actively investigated with concern in the environmental effects if using conventional fuels from reservoir of fossil fuels. Hence, to counter these consequences, Sustainable Fuels (SF) is investigated as it is considered a renewable source of fuel. Thus, this study aims to establish an experiment to determine the suitability of biomass fuel by using soybean and waste cooking oil feedstocks. An experiment is set up to produce biomass fuel by using feedstock from different biomass particularly from soybean oil, a first-generation edible feedstock and waste cooking oil, a second-generation nonedible feedstock. The method chosen to produce biomass fuel is transesterification. The experiment will test the effects of a catalyst, namely solid Potassium Hydroxide, KOH, with three levels of concentration 0.75%, 1%, and 1.5% w/w KOH. Once the biomass fuel is produced it will undergo a series of tests to study the effect of parameters such as density, kinematic viscosity, caloric value, acid value and Fatty Acid Methyl Ester (FAME). The results show that using the feedstock 0.75 w/w% of KOH, the yield of biomass fuel is the most for both feedstocks. It is noted that soybean oil yields slightly greater feedstock than waste cooking oil. The density for both feedstock is very similar at 0.87-0.88 g/cm3. The acid value of biomass fuel produced from waste cooking oil is much higher than soybean oil at 0.28 but still under the acceptance range of 0.5. The concentration of catalyst used is a major factor in the yield of biomass fuel. It is also noted that the first-generation edible feedstock of soybean oil produces greater quality of biomass fuel. Nevertheless, first-generation feedstock still poses the food competition threat in comparison to second-generation feedstock. Therefore, establishment of the second-generation feedstock from waste cooking oil produces biomass fuel that is close to the quality of soybean oil, it is a more preferred feedstock compared to soybean oil.