Hao Wang

Dr. Hao Wang

Huairou Laboratory, Beijing 101499, China
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 October 2019 in Advanced Materials
Verified
Journal Article
Closed access
PDF file
Hao WangHao Wang
Hao Wang
CZCheng Zhu
Cheng Zhu
LLLang Liu
Lang Liu
SMSai Ma
Sai Ma
PLPengfei Liu
Pengfei Liu
QCQi Chen
Qi Chen

30 July 2021 in Science
Verified
Journal Article
Closed access
PDF file
NLNengxu Li
Nengxu Li
XNXiuxiu Niu
Xiuxiu Niu
LLLiang Li
Liang Li
Hao WangHao Wang
Hao Wang
ZHZijian Huang
Zijian Huang
HZHuanping Zhou
Huanping Zhou
Evening out the heat: The conversion of precursors into the active layer of perovskite solar cells normally occurs by heating the underlying substrate. Conversion tends to occur near the top of the film, where solvent is lost, and unwanted preheating of reactants occurs near the substrate before the reaction. Li et al . show that the use of a surrounding heat transfer oil (anisole) leads to more rapid and even heating, removes solvent, and avoids air and water contamination effects. The larger grains and more uniform films led a much greater retention of efficiency in moving from small-area to large-area devices. —PDS

28 September 2020 in Energy & Environmental Science
Verified
Journal Article
Closed access
PDF file
NYNing Yang
Ning Yang
CZCheng Zhu
Cheng Zhu
YCYihua Chen
Yihua Chen
HZHuachao Zai
Huachao Zai
CWChenyue Wang
Chenyue Wang
QCQi Chen
Qi Chen
Long-term stability is an essential requirement for perovskite solar cells (PSCs) to be commercially viable. Heterojunctions built by low-dimensional and three-dimensional perovskites (1D/3D or 2D/3D) help to improve the stability of PSCs. However, the insulated organic cations of low-dimensional perovskite impede the transport of carriers, decreasing the power conversion efficiency (PCE) of PSCs. Herein, we introduce an in situ cross-linking polymerizable propargylammonium (PA+) to the 3D perovskite film at surfaces and grain boundaries to form a 1D/3D perovskite heterostructure. This passivation strategy not only significantly improves the interfacial carrier transport but also releases residual tensile strain in perovskite films. As a result, the corresponding devices achieve a champion PCE of 21.19%, while maintaining 93% of their initial efficiency after 3055 h of continuous illumination under maximum power point (MPP) operating conditions.

8 August 2021 in Advanced Materials
Verified
Journal Article
Closed access
PDF file
JDJie Dou
Jie Dou
CZCheng Zhu
Cheng Zhu
Hao WangHao Wang
Hao Wang
YHYing Han
Ying Han
SMSai Ma
Sai Ma
QCQi Chen
Qi Chen

30 January 2020 in Advanced Energy Materials
Verified
Journal Article
Closed access
PDF file
SMSai Ma
Sai Ma
YBYang Bai
Yang Bai
Hao WangHao Wang
Hao Wang
HZHuachao Zai
Huachao Zai
JWJiafeng Wu
Jiafeng Wu
QCQi Chen
Qi Chen

17 May 2022 in Advanced Materials
Verified
Journal Article
Open access
LWLina Wang
Lina Wang
QSQizhen Song
Qizhen Song
FPFengtao Pei
Fengtao Pei
YCYihua Chen
Yihua Chen
JDJie Dou
Jie Dou
QCQi Chen
Qi Chen
Perovskite/silicon tandem solar cells are promising to penetrate photovoltaic market. However, the wide‐bandgap perovskite absorbers used in top‐cell often suffer severe phase segregation under illumination, which restricts the operation lifetime of tandem solar cells. Here, a strain modulation strategy to fabricate light‐stable perovskite/silicon tandem solar cells is reported. By employing adenosine triphosphate, the residual tensile strain in the wide‐bandgap perovskite absorber is successfully converted to compressive strain, which mitigates light‐induced ion migration and phase segregation. Based on the wide‐bandgap perovskite with compressive strain, single‐junction solar cells with the n–i–p layout yield a power conversion efficiency (PCE) of 20.53% with the smallest voltage deficits of 440 mV. These cells also maintain 83.60% of initial PCE after 2500 h operation at the maximum power point. Finally, these top cells are integrated with silicon bottom cells in a monolithic tandem device, which achieves a PCE of 26.95% and improved light stability at open‐circuit.