maycon athayde

Dr. maycon athayde


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 December 2017 in Mineral Processing and Extractive Metallurgy Review
Verified
Journal Article
Closed access
MAmaycon athayde
maycon athayde
MCMauricio Cota
Mauricio Cota
MCMaurício Covcevich
Maurício Covcevich
Drying is a critical process step to achieve excellent pellet quality in pelletizing process. The complexity and energy consumption toward moisture removing, especially for highly hydrated iron ore, increased the need for breakthrough enhancements to this process. The present study has evaluated kinetics parameters of the moisture release from iron ore green pellet using energy transmitted through microwave (frequency of 2.45 GHz). The influence of pellet size and output power on the moisture effective diffusivity (Deff) and the drying activation energy (Ea) were evaluated. The results make possible to compare the cutting-edge approach with traditional convective drying. Pellet physical quality was investigated through the green crushing strength (GCS), which shows smooth reduction in earlier stages, however not affecting the final dry GCS results. Bonded hematite reduction and calcination of goethite was identified at the microstructure through reflected light microscopy, SEM showed micro cracks formation in several grains.

28 December 2017 in Mineral Processing and Extractive Metallurgy Review
Verified
Journal Article
Closed access
MAmaycon athayde
maycon athayde
SNSergio Fernandes Nunes
Sergio Fernandes Nunes
MBMauricio Covcevich Bagatini
Mauricio Covcevich Bagatini
Pellet production is constantly optimized considering different aspects of the production chain from run of mining (ROM) to metallic iron. Industrially, the trade-off between an optimum pellet-size-ratio and the maximum performance in the steel production chain is a relevant subject. The present case study at a Brazilian operation shows the impact of different pellet size fractions on performance of operation, improvements on the fired pellets, less fine generation during handling, and superior metallurgical behavior during the reduction process, resulting in the production of direct reduction iron (DRI) that add more value to the economic performance of the electric arc furnaces (EAF).

6 September 2018 in Materials Research
Verified
Journal Article
Open access
PDF file
MAmaycon athayde
maycon athayde
MBMaurício Covcevich Bagatini
Maurício Covcevich Bagatini
MFMaurício Cota Fonseca
Maurício Cota Fonseca
Drying has became critical to iron ore pellet production, due to increasing inability to withdrawal moisture from the green pellets, especially faced by goethitic iron ore producers. Most of the existing pelletizing furnaces do not support increase heating rates nor changes in furnaces length, without compromise pellet quality. The present study evaluates an innovative alternative for the actual fully convective drying process composed by an up-draught drying (UDD) and down-draught drying stage (DDD), through the application of microwave energy to assist the existing process. In the present work, the process was simulated in a pot grate where industrial parameters can be simulated. The microwave generator (power input of 10 MW and 915 MHz) was connected in a traditional static pot grate at the hood by a microwave conductor. The experiments show elimination of the over-wet zone at the upper layer of pellet observed at the traditional process. A reduction greater than 7% of the moisture in UDD was achieved, while the convective process adds extra moist to the green pellets modifying the pellet shape.

8 October 2018 in Mining, Metallurgy & Exploration
Verified
Journal Article
Closed access
PDF file
MAmaycon athayde
maycon athayde
MBMaurício Covcevich Bagatini
Maurício Covcevich Bagatini

1 June 2018 in Mineral Processing and Extractive Metallurgy Review
Verified
Journal Article
Closed access
MAmaycon athayde
maycon athayde
LCLuiz Claudio Von Sperling Cotta
Luiz Claudio Von Sperling Cotta
MBMauricio Covcevich Bagatini
Mauricio Covcevich Bagatini
Production of iron ore pellets with enough strength to resist the transport and reduction on reactors requires an accurate adjustment of traveling grate furnace process parameters. The firing zone is the most energy intensive step to ensure quality and this study based on Lean Six Sigma methodology to evaluate and optimize the thermal profile through temperature fine-tuning. A pilot scale assessment aid to analyze physical, chemical, metallurgical and microstructure properties of pellets through different temperatures to accurate industrial implementation. The validation of lab-scale trials was concluded by industrial implementation to guarantee the quality, productivity and reduced costs.

28 March 2020 in Mining, Metallurgy & Exploration
Verified
Journal Article
Closed access
PDF file
ATAnderson Denadai Thomazini
Anderson Denadai Thomazini
ETEduardo Poltronieri Trés
Eduardo Poltronieri Trés
FMFrancisco de Assis Dutra Macedo
Francisco de Assis Dutra Macedo
MAmaycon athayde
maycon athayde
GBGilvandro Bueno
Gilvandro Bueno
RNRossano Augusto Pilon Nunes
Rossano Augusto Pilon Nunes