Reflective cracking is a combination of Mode I (opening) and Mode II (sliding) fracture, or Mixed-Mode fracture. The Single-Edge Notch Beam [SE(B)] test was used to analyze Mixed-Mode fracture characteristics of three asphalt concrete mixtures in the laboratory. The peak loads were similar across all three mixtures, emphasizing the importance of fracture mechanics when analyzing low temperature characteristics of asphalt concrete. The fracture work successfully differentiated the three mixtures, and showed that the fracture work increased as the level of Mode II increased. Simulations showed the damage in the mixtures evolved differently, with the more compliant mixtures showing a higher percentage of dissipated creep damage, and the more quasi-brittle mixture showing a higher percentage of dissipated fracture damage.
13 February 2018 in International Journal of Pavement Engineering
With the development of modified emulsified asphalt, cold recycling technique has the potential to be used in pavement layers closer to surface. Three modified emulsified asphalt binders were carefully prepared by adding Styrene–butadiene rubber (SBR) latex, styrene-ethylene–butylene-styrene (SEBS) copolymer and chloroprene rubber (CR) latex, respectively. In order to characterise how the properties of asphalt binder related to the rutting of cold recycling mix. The high temperature Dynamic Shear Rheometer (DSR) and Multiple Stress Creep Recovery (MSCR) tests were conducted under varying test temperatures ranging from 46 to 76 °C. An advanced cyclic creep test was conducted to study the rutting resistance of the full-depth pavement structures with cold recycling mix. According to the test results, the high-temperature performance were improved significantly by adding the polymer modifiers, and adding CR latex seems to be a more effective way to improve the rutting resistance of emulsified asphalt. Results from MSCR test under temperatures no less than 64 °C shows a better correlation with test results from the advanced cyclic creep test than the G*/sin δ from high temperature DSR test. Thus, by carefully choosing the test temperature and stress, the MSCR test shows promise to be a surrogate to the existing DSR test.
11 March 2016 in Road Materials and Pavement Design
With the government promoting use of hot in-place recycling (HIR) in China, the performance of HIR pavement has become a topic of intensive study. HIR processes had been using rejuvenator to restore properties of aged binder in the past, but it was found that rejuvenator is not sufficient in reconstituting the physical and chemical properties of aged polymer-modified asphalt, and that it is inclined to increase rutting potential. Sryrene–butadiene rubber (SBR) latex was then brought up as a proper substitute for rejuvenator in recent years. In this paper, both rejuvenator and SBR latex are evaluated and compared in the HIR process with modified asphalt binder. Comprehensive tests in laboratory and field trials were conducted to evaluate the properties of recycled binder and recycled mixtures. The results show that SBR latex increases the viscosity of aged binder, meanwhile it improves the rutting resistance and fatigue cracking resistance of reclaimed asphalt pavement (RAP) significantly, and that rejuvenator has adverse effect on both rutting and fatigue cracking resistance of RAP. Also SBR latex shows better application performance than rejuvenator in the moisture susceptibility and low-temperature cracking resistance of RAP. Both HIR trials with rejuvenator and SBR latex have maintained a high level of service since open to traffic, but trials with SBR latex is observed to be more promising in rutting resistance than those with rejuvenator.
17 February 2019 in International Journal of Pavement Engineering
Mastic, a compound consisting of an asphalt binder and a mineral filler, is an important ingredient in asphalt mixtures, as it is responsible for critical adhesion and viscoelasticity. The rheological properties of mastic are strongly correlated with the rutting potential of asphalt pavement. To explore the impact of filler on the rheological response, three types of asphalt binders and eight types of filler contents were used to fabricate the mastic samples. A modified version of multiple stress creep recovery (MSCR) test selected in this study was regarded as a superior protocol by which to test the rutting potential of asphalt binder and mastic. Based on the rheological behaviour, the 1.0 mm parallel plate gap height was recommended for use in the dynamic shear rheometer (DSR) to evaluate mastic in the MSCR test. The test yielded excellent results with regard to modifier contents, filler contents and stress levels. The regression analysis proved that percent recovery (%R) was a better index for estimating the rheological ability of mastic. Based on the results for %R, the linear viscoelastic region of modified mastic could be expanded by increasing the filler content, while neat mastic demonstrated poor recovery under high stress regardless of filler content. Based on the rheological response, the recommended filler contents were 100%, 120% and 50% for the mastics with 4.0% SBS-modified binder, 3.5% SBS-modified binder and neat binder, respectively.
In order to investigate the fatigue cracking resistance of engineered cementitious composites (ECC) used in in total life pavement, the semi-circular bending (SCB) test and improved three-point bending fatigue test (ITBF) were utilized in this study. The digital image correlation (DIC) method was also utilized to track the surface strain fields of specimens during the SCB test. X-ray computed tomography (CT) and digital image processing (DIP) technologies were applied to measure the internal-crack distribution of the ITBF specimen. The results of the SCB test showed that the fatigue cracking damage process of ECC can be divided into three stages and that the cracking stable propagating stages occupied the main part, which indicates that ECC has excellent ductility and toughness and could work very well with existing cracks. The ITBF results showed that the fatigue cracking resistance of ECC was better than epoxy asphalt concrete (EAC). In addition, the internal-crack distribution along the depth direction of the ITBF specimen could be presented well by the image pixel statistical (IPS) method based on CT scanning of image slices. It could be found that multiple cracks propagate simultaneously in ECC, instead of a single crack, under the OSBD pavement working condition.
1 August 2017 in Journal of Materials in Civil Engineering
This study carried out laboratory investigations of fatigue damage development of hot mix asphalt (HMA) by semicircular bending (SCB) test. Strength of the HMA specimen was first investigated at different loading rates, the results of which indicate an exponential relationship between strength and loading rate. The SCB fatigue test at stress-control mode was then performed at six levels of stress-strength ratio (SSR). Two fatigue life prediction models have been established accordingly based on the concepts of the nominal SSR and the authentic SSR. The latter model can better predict fatigue behaviors. As follows, another round of SCB fatigue test was continued to investigate the relationship between residual strength and fatigue damage evolution. Analysis of test results indicate that fatigue damage evolution is nonlinear and consists of two components: the accumulative damage development and last-cycle damage jump. A fatigue damage evolution model has been finally built based on the residual strength, which can capture the “sudden death” phenomenon of the fatigue damage process at stress-control mode.