Gonçalo Soares

Mr. Gonçalo Soares

INEGI – Institute of Science and Innovation in Mechanical and Industrial Engineering, Porto, Portugal
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2023 in Metals
Verified
Journal Article
Open access
PDF file
Gonçalo SoaresGonçalo Soares
Gonçalo Soares
RNRui Neto
Rui Neto
Rui MadureiraRui Madureira
Rui Madureira
RSRui Soares
Rui Soares
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
LALuís Araújo
Luís Araújo
AlSi12(Fe), AlSi10Mg(Fe), AlSi10MnMg, and AlMg4Fe2 die-casting alloys were produced by high-pressure die casting (HPDC) and vacuum-assisted high-pressure die casting (VADC) under a vacuum level of 200 mbar. The chemical composition, hardness, gas and shrinkage porosity, and mechanical properties were analyzed. The parts under study were subjected to a T6 heat treatment. The VADC led to a decrease in the percentage of defects in the as-cast state for all the alloys, due to a reduction in the amount of gas porosities. After heat treatment, the quantity of gas and shrinkage porosities increased. The efficiency and level of vacuum used were not sufficient to improve the mechanical properties in the as-cast state. The ductility of AlSi10Mg(Fe) and AlSi10MnMg alloys was improved after heat treatment; however, the YS and UTS of AlSi10Mg(Fe) did not increase. The primary aluminum alloys presented higher elongation values than the secondary aluminum alloys due to the reduced amount of the needle-like β-Al5FeSi phase.

16 September 2024 in Metals
Verified
Journal Article
Open access
PDF file
RGRui Gomes
Rui Gomes
Gonçalo SoaresGonçalo Soares
Gonçalo Soares
Rui MadureiraRui Madureira
Rui Madureira
Rui Pedro SilvaRui Pedro Silva
Rui Pedro Silva
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
Cristina M. FernandesCristina M. Fernandes
Cristina M. Fernandes
In this work, we intended to study the effect of heat treatments (T5 and flash T6) on blistering, mechanical properties and microstructure for different parts produced by vacuum-assisted HPDC. These parts were produced with primary and secondary aluminium alloys (AlSi10MnMg alloy and AlSi10Mg(Fe) alloy, respectively). The parts presented blisters for all combinations of temperature (between 360 °C and 520 °C) and stage times (15 and 30 min) of solution heat treatments. However, when subjected to the T5 heat treatment, blisters were no longer visible. With this heat treatment, there was an increase in yield strength of 64% for both aluminium alloys and an increase in UTS of 31% in AlSi10Mg(Fe) alloy and of 24% in AlSi10MnMg alloy, when compared to the mechanical properties in the as-cast state. However, there was a decrease in ductility. The AlSi10Mg(Fe) alloy presented a lot of contaminations (especially iron), which impaired the mechanical properties compared to the primary aluminium alloy, AlSi10MnMg.

10 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
Filipe MonteiroFilipe Monteiro
Filipe Monteiro
Gonçalo SoaresGonçalo Soares
Gonçalo Soares
Rui MadureiraRui Madureira
Rui Madureira
Rui Pedro SilvaRui Pedro Silva
Rui Pedro Silva
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
AEAntónio José Esteves
António José Esteves
The low-pressure die casting (LPDC) process was experimentally and numerically studied to produce AlSi7Mg0.3 components such as steering knuckles. Steering knuckles are important safety components in the context of a vehicle’s suspension system, serving as the mechanical interface that facilitates the articulation of the steering to control the front wheel’s orientation, while simultaneously bearing the vertical load imposed by the vehicle’s weight. This work focuses on the development of a numerical model in ProCAST®, replicating the production of the aforementioned part. The model analyses parameters such as the filling dynamics, solidification process, and presence of shrinkage porosities. For the purpose of evaluating the quality of the castings, six parts were produced and characterised, both mechanically (tensile and hardness tests) and microstructurally (porosity and optical microscopy analysis). When correlating simulation results with the available experimental data, it is possible to conclude that the usage of the LPDC process is a viable alternative to the use of steels and other metals for the production of very high-quality castings while using lighter alloys such as aluminium and magnesium in more demanding applications.