Nurudeen Adekunle Raji

Dr. Nurudeen Adekunle Raji


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2013 in Research Journal of Applied Sciences, Engineering and Technology
Verified
Journal Article
Open access
PDF file
NRNurudeen Adekunle Raji
Nurudeen Adekunle Raji
OOO.O. Oluwole
O.O. Oluwole
The objective of this study is to investigate the influence of service situation on the mechanical properties of plain nails manufactured from low carbon steel. The influence of the degree of cold drawing on the mechanical properties and strain hardening of the material is investigated by tensile test experimentation. The stress-strain relationships of the cold-drawn low carbon steel were investigated over the 20, 25, 40 and 55% degree of drawn deformation for the manufacture of 4, 3, 21⁄2 and 2 inches nails, respectively. The true stress-strain curves were analyzed to obtain the yield strength and tensile strength of the cold drawn steel. It is shown that the yield strength, tensile strength, hardness and toughness of the low carbon steel reduce with increasing degree of cold-drawn deformation. The micrographs of the deformed samples obtained using optical microscope shows that the grain structure elongates in the direction of the drawing operation and misorientation of the grains set in at 40 and 55% degree of deformation. The difference in yield strength was attributed to the strain hardening, resulting from the different degrees of drawn deformation.

1 September 2017 in TRANSACTIONS of the VŠB – Technical University of Ostrava, Safety Engineering Series
Verified
Journal Article
Open access
AMAdekunle I. Musa
Adekunle I. Musa
AYAbiodun A. Yussouff
Abiodun A. Yussouff
NRNurudeen Adekunle Raji
Nurudeen Adekunle Raji
TOTemitayo S. Ogedengbe
Temitayo S. Ogedengbe
RSRasheed O. Saheed
Rasheed O. Saheed
The objective of this study is to undertake an Ergonomic Scrutiny of Desecrate Management Industry. Ten (10) employees of the parking and collection department of Kim Waste Management Authority (KWMA) were selected. Their activities were video and recorded while working and their different postures were analyzed using Rapid Entire Body Assessment (REBA) and Rapid Upper Limb Assessment (RULA). Result showed that 10 % were at medium risk; 40 % were at high risk and 50 % were at very high risk for the workers in KWMA. It as discovered that workers are subjected to Musculoskeletal Disorder (MSDs) as a result of the postures adopted during the work process.

16 March 2018 in Engineering and Technology Research Journal
Verified
Journal Article
Closed access
NRNurudeen Adekunle Raji
Nurudeen Adekunle Raji
JOJoshua O. Olaleye
Joshua O. Olaleye
RORotimi O. Ogunleye
Rotimi O. Ogunleye
TATemiloluwa A. Anibaba
Temiloluwa A. Anibaba

1 June 2024 in Journal of Production Engineering
Verified
Journal Article
Closed access
NRNurudeen Adekunle Raji
Nurudeen Adekunle Raji
RKRafiu O. Kuku
Rafiu O. Kuku
AOAdeshola O. Openibo
Adeshola O. Openibo
LSLagos State Ministry Of Transportation Transport And Commuter Services
Lagos State Ministry Of Transportation Transport And Commuter Services
EOEmmanuel A. Owolabi
Emmanuel A. Owolabi
In this study, the influence of the compression ratio on the performance characteristics of a gasoline engine was investigated in detail using COMSOL simulations. Four compression ratios — 8, 9, 10 and 11 — were investigated at different engine speeds between 1000 and 1800. The analysis focused on power output, braking performance and fuel consumption in order to decipher the complicated relationships between compression ratios and engine dynamics. The results showed a significant increase in power output with increasing compression ratio, highlighting the delicate balance required for optimal power generation. Braking power increased with higher compression ratios, indicating a potential improvement in braking performance. In addition, the study showed a correlation between increased fuel consumption and higher compression ratios, highlighting the need for strategic fuel-saving measures. These results contribute to the understanding of gasoline engine behavior and provide insights into the trade-offs that need to be made when adjusting the compression ratio. Recommendations include experimental validation, exploration of dynamic compression control, research into integrated braking systems, investigation of sustainable fuel strategies and a focus on multi-metric optimization. The observed increase in power output at higher compression ratios highlights an important aspect of engine optimization. Engineers and researchers need to carefully consider compression ratio adjustments to ensure optimal power generation while maintaining efficiency. This insight can guide the development of engines that strike an ideal balance between power and fuel efficiency.

1 December 2024 in Journal of Production Engineering
Verified
Journal Article
Closed access
NRNurudeen Adekunle Raji
Nurudeen Adekunle Raji
RKRafiu O. Kuku
Rafiu O. Kuku
ABAbdullateef O. Bakare
Abdullateef O. Bakare
MOMedekannu M. Ogunbiyi
Medekannu M. Ogunbiyi
TMTobiloba I. Morafa
Tobiloba I. Morafa
Gearbox fault detection plays a crucial role in ensuring the reliable operation of machinery and preventing costly downtime. This research thesis aims to develop and evaluate ensemble learning techniques for accurate detection of gearbox broken tooth conditions using vibration data from SpectraQuest's Gearbox Fault Diagnostics Simulator. The dataset comprises vibration readings from sensors under both healthy and broken tooth conditions. A thorough analysis of the Gearbox Fault Diagnosis Dataset was conducted, integrating time and frequency domain analyses to inform feature engineering. A comprehensive comparative analysis of bagging, boosting, stacking, and voting approaches was conducted. The standout performer is the AdaBoostClassifierET, achieving an accuracy of 87.56%, precision of 88.36%, recall of 86.38%, and an F1 score of 87.36%. Bagging methods also exhibit commendable performance, with the BaggingClassifierET achieving an accuracy of 87.38%, precision of 87.17%, recall of 87.50%, and an F1 score of 87.34%. The research also highlights the significance of base model choices in ensemble techniques, as different base model choices yielded different results in all four techniques. The study surpasses previous work by incorporating a comprehensive set of ensemble techniques, advanced feature engineering informed by time and frequency domain analyses, and a nuanced evaluation of overfitting concerns.

1 January 2010 in Journal of Engineering and Applied Sciences
Verified
Journal Article
Closed access
NRNurudeen Adekunle Raji
Nurudeen Adekunle Raji
VOVitalis O. Ozor
Vitalis O. Ozor
AEAndrew A. Erameh
Andrew A. Erameh
Transient Response of Damped Beat-Up Mechanism for Narrow Looms