U-pipes for ground source heat pump (GSHP) installations are generally inserted in vertical boreholes back-filled with pumpable grouts. Grout thermal conductivity is a crucial parameter, dominating the borehole thermal resistance and impacting the heat exchanger efficiency. In order to seal the borehole and prevent leakages of the heat carrier fluid, grouting materials are also hydraulically impermeable, so that groundwater flow inside the borehole is inhibited. The influence of groundwater flow on the borehole heat exchangers (BHE) performance has recently been highlighted by several authors. However groundwater impact and grouting materials influence are usually evaluated separately, disregarding any combined effect. Therefore simulation is used to investigate the role of the thermal and hydraulic conductivities of the grout when the BHE operates in an aquifer with a relevant groundwater flow. Here 3 main cases for a single U-pipe in a sandy aquifer are compared. In Case 1 the borehole is back-filled with the surrounding soil formation, while a thermally enhanced grout and a low thermal conductivity grout are considered in Case 2 and Case 3 respectively. Simulations are carried out maintaining the inlet temperature constant in order to reproduce the yearly operation of the GSHP system. For each of the 3 cases three different groundwater flow velocities are considered. The results show that a high thermal conductivity grout further enhances the effects of a significant groundwater flow. The conditions when neglecting the grout material in the numerical model does not lead to relevant errors are also identified.

Several remediation technologies are currently used to address groundwater pollution. “Pump and treat” (P&T) is probably one of the most widely applied, being a process where contaminated groundwater is extracted from the subsurface by pumping and then treated before it is discharged or reinjected into the aquifer. Despite being a very adaptable technology, groundwater remediation is often achieved in long and unsustainable times because of limitations due to the hydrogeological setting and contaminant properties. Therefore, the cost–benefit analysis over time results in an inefficient system and a preliminary evaluation of the clean-up time is crucial. The aim of the paper is to compare, in an integrated manner, the application of some models to estimate the time to compliance of a P&T system in relation to the specific hydrogeological condition. Analytical solutions are analyzed and applied to an industrial site and to a synthetic case. For both cases, batch flushing and the advection-dispersion-retardation (ADR) model underestimate remediation times comparing the results to real or simulated monitoring data, whereas the Square Root model provided more reliable remediation times. Finally, for the synthetic case, the reliability of analytical approaches and the effects of matrix diffusion are tested on the basis of a numerical groundwater transport model specifically implemented, which confirm the results of the analytical methods and the strong influence of the matrix diffusion on the results.

Groundwater contamination by chlorinated hydrocarbons is a worldwide problem that poses important challenges in remediation processes. In Italy, the Legislative Decree 152/06 defines the water quality limits to be obtained during the cleanup process. In situ bioremediation techniques are becoming increasingly important due to their affordability and, under the right conditions, because they can be more effective than conventional methodologies. In the initial feasibility study phase, the numerical modeling supports the reliability of each technique. Two different codes, BIOCHLOR and PHREEQC were discussed and compared assuming different field conditions. Isotopic Fractionation-Reactive Transport Models were then developed in one synthetic and one simple field case. From the results, the two codes were in agreement and also able to demonstrate the Monitored Natural Attenuation processes occurring at the dismissed site located in Italy. Finally, the PHREEQC model was used to forecast the remediation time frame by MNA, hypothesizing a complete source cleanup: a remediation time frame of about 10–11 years was achieved by means of natural attenuation processes.

A proper management of fresh groundwater lenses in small islands is required in order to avoid or at least limit uncontrolled saltwater intrusion and guarantee the availability of the resource even during drought occurrences. An accurate estimation of the freshwater volume stored in the subsoil is a key step in the water management decision process. This study focused on understanding the hydrogeological system behaviour and on assessing the sustainable use of the groundwater resource in Nauru Atoll Island (Pacific Ocean). A first phase, concerning the hydrogeological characterization of the island, highlighted the occurrence of few drought-resilient freshwater lenses along the seashore. The second part of the study focused on the characterization of a freshwater lens found in the northern coastal area and identified such area as the most suitable for the development of groundwater infrastructures for water withdrawal. The characterization activities allowed quantifying the freshwater lens thickness and volume in order to assess the capability to satisfy the population water demand. A geo-electrical tomography survey was carried out, and a 3D density-dependent numerical model was implemented in SEAWAT. The model results demonstrated that in small islands freshwater can unexpectedly accumulate underground right along the seashore and not in the centre of the island as is commonly believed. Furthermore, the model can constitute a useful tool to manage the groundwater resources and would allow the design of sustainable groundwater exploitation systems, avoiding saltwater intrusion worsening.