Debashis Maji

Dr. Debashis Maji

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2011 in Surface and Interface Analysis
Verified
Journal Article
Closed access
PDF file
DMDebashis Maji
Debashis Maji
SLS. K. Lahiri
S. K. Lahiri
SDSoumen Das
Soumen Das

27 November 2020 in IEEE Sensors Journal
Verified
Journal Article
Closed access
KTK. Thiyagarajan
K. Thiyagarajan
RGRajini G.K
Rajini G.K
DMDebashis Maji
Debashis Maji
Accurate measurement and monitoring of respiration is vital in patients affected by severe acute respiratory syndrome coronavirus – 2 (SARS-CoV-2). Patients with severe chronic diseases and pneumonia need continuous respiration monitoring and oxygenation support. Existing respiratory sensing techniques require direct contact with the human body along with expensive and heavy Holter monitors for continuous real-time monitoring. In this work, we propose a low-cost, non-invasive and reliable paper-based wearable screen printed sensor for human respiration monitoring as an effective alternative of existing sensing systems. The proposed sensor was fabricated using traditional screen printing of multi-walled carbon nanotubes (MWCNTs) and polydimethylsiloxane (PDMS) composite based interdigitated electrodes on paper substrate. The paper substrate was used as humidity sensing material of the sensor. The hygroscopic nature of paper during inhalation and exhalation causes a change in dielectric constant, which in turn changes the capacitance of the sensor. The composite interdigitated electrode configuration exhibited better response times with a rise time of 1.178s being recorded during exhalation and fall time of 0.88s during inhalation periods. The respiration rate of sensor was successfully examined under various breathing conditions such as normal breathing, deep breathing, workout, oral breathing, nasal breathing, fast breathing and slow breathing by employing it in a wearable mask, a mandatory wearable product during the current COVID-19 pandemic situation.Thus, the above proposed sensor may hold tremendous potential in wearable/flexible healthcare technology with good sensitivity, stability, biodegradability and flexibility at this time of need.

11 June 2021 in IEEE Sensors Journal
Verified
Journal Article
Closed access
TKThiyagarajan K.
Thiyagarajan K.
RGRajini G.K
Rajini G.K
DMDebashis Maji
Debashis Maji
Personalized mobile healthcare integrated with various wearable devices has become a significant area of interest in the present era. In the current research work, a flexible, wearable and disposable paper-based continuous skin temperature monitoring sensor for early medical prognosis and accurate diagnosis of body temperature-related ailments, such as COVID-19, is proposed. Conventional screen-printing and drop-casting techniques were used to fabricate the proposed sensor using MWCNTs as the sensing material and paper as the substrate. The linearity, stability, repeatability and durability of the sensors were tested from 29°C (room temperature) to 60°C. A thin sheet of PET was laminated over the sensor surface to ascertain its stability toward environmental effects and physical movements, and a response time of ~13 s and a recovery time of ~38 s with a sensitivity of -0.0685% °C-1 were recorded. The efficacy of the proposed sensor was ascertained by placing it at different body locations on a human subject and comparing it with a standard thermocouple and IR sensor. The sensor even helped to effectively distinguish minimal temperature variations between various regions of the body. Furthermore, the feasibility of the fabricated temperature sensor as a temperature-based tactile sensor for robotics/artificial skin applications and as a noncontact breath monitoring device for use in personalized healthcare monitoring applications was investigated.

7 December 2015 in Scientific Reports
Verified
Journal Article
Open access
DMDebashis Maji
Debashis Maji
DDDebanjan Das
Debanjan Das
JWJyoti Wala
Jyoti Wala
SDSoumen Das
Soumen Das
Development of flexible sensors/electronics over substrates thicker than 100 μm is of immense importance for its practical feasibility. However, unlike over ultrathin films, large bending stress hinders its flexibility. Here we have employed a novel technique of fabricating sensors over a non-planar ridge topology under pre-stretched condition which not only helps in spontaneous generation of large and uniform parallel buckles upon release, but also acts as stress reduction zones thereby preventing Poisson’s ratio induced lateral cracking. Further, we propose a complete lithography compatible process to realize flexible sensors over pre-stretched substrates thicker than 100 μm that are released through dissolution of a water soluble sacrificial layer of polyvinyl alcohol. These buckling assisted flexible sensors demonstrated superior performance along different flexible modalities. Based on the above concept, we also realized a micro thermal flow sensor, conformally wrapped around angiographic catheters to detect flow abnormalities for potential applications in interventional catheterization process.

3 October 2017 in Biomedical Materials
Verified
Journal Article
Closed access
PDF file
JWJyoti Wala
Jyoti Wala
DMDebashis Maji
Debashis Maji
SDSoumen Das
Soumen Das
The tunable mechanical and physical properties of polydimethylsiloxane (PDMS) are commonly utilized for studying cellular dynamics. However, the inherent hydrophobic nature of PDMS limits its application as a cell culture film. Various surface modification techniques render PDMS films hydrophilic, altering their surface chemistry, elasticity, roughness and the cell attachment of anchorage-dependent cell types to the films. The surface properties of thin films lead to the alteration of the biomechano-physical properties of cells, so they can be used as a mechanical signature for the viability testing of different types of cell, such as normal and cancerous ones. In this study, 3T3 fibroblast and HaCaT keratinocyte cells were grown on different pristine and oxidized PDMS compositions by varying their base-to-curing-agent ratios (w/w). The enhanced wettability favors the cell spreading and growth rate of both 3T3 and HaCaT cells, and it varies with the film’s surface chemistry and elasticity. This study focuses on the importance of understanding how various surface modification methods, like oxygen plasma and piranha treatment, can impact cell–cell and cell–substrate interaction for different cell types, thereby assisting in the preparation of various PDMS-based biomedical devices.

13 February 2014 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
DMDebashis Maji
Debashis Maji
SDSoumen Das
Soumen Das