The development of novel dithienylethene-based fluorescence switches in the aggregated state, and the solid state is highly desirable for potential application in the fields of optoelectronics and photopharmacology. In this contribution, three novel triphenylethene-functionalized dithienylethenes (1–3) have been designed and prepared by appending triphenylethene moieties at one end of dithienylethene unit. Their chemical structures are confirmed by 1H NMR, 13C NMR, and HRMS (ESI). They display good photochromic behaviors with excellent fatigue resistance upon irradiation with UV or visible light in Tetrahydrofuran (THF) solution. Before irradiation with UV light, they exhibit Aggregation Induced Emission (AIE) properties and luminescence behaviors in the solid state. Moreover, upon alternating irradiation with UV/visible light, they display effective fluorescent switching behaviors in the aggregated state and the solid state. The experimental results have been validated by the Density Functional Theory (DFT) calculations. Thus, they can be utilized as novel fluorescence switches integrated in smart, solid-state optoelectronic materials and photopharmacology.
Single-walled carbon nanotubes (SWCNTs) have superior mechanical properties which originate from a strong C-C covalent bond and unique nanostructure. Chirality, one of the helical structural parameters of SWCNTs, leads to differences in mechanical performance. In this work, molecular dynamics (MD) simulation was performed to analyze engineering Poisson’s ratio (EPR) and incremental Poisson’s ratio (IPR) of SWCNTs with different chiral angles, respectively, under tensile and compressive load, as well as the chiral effect on rigidity. We reported the minimum EPR for (4, 1) SWCNT and obtained the distribution and trend of EPR which is dependent on chiral index m. In addition, a new observation showed two exactly opposite trends of EPR existing not only in tension and compression but also in the longitudinal and radial directions. Furthermore, we found that the critical strain, over which SWCNT would be auxetic, ranged from 6% to 18% and was also chirality-dependent. Three representative SWCNTs with chiral angle of 0° (zigzag), 10.89° (chiral), and 30° (armchair) were selected for the mechanism study of auxeticity. Finally, a method of the contribution to radial strain for two main deformation modes proposed in this paper could well explain the negative IPR phenomenon.
Graphene is considered to be one of the most promising reinforcement phases for nanocomposites due to its unique two-dimensional planar structure with excellent mechanical properties. After the design of origami, the 2D material will obtain a negative Poisson’s ratio in the in-plane direction and become a metamaterial with unusual mechanical properties. Inspired by this, an origami pattern is adopted for graphene at an atomic scale using a molecular dynamics (MD) approach, and then origami graphene is embedded into a single-crystal copper matrix to obtain origami graphene/copper nanocomposites with auxetic behaviors. In the modeling, the periodic boundary condition is chosen to exhibit the Poisson’s ratio of the whole system. Under the isothermal–isobaric ensemble, the interactions between C-C, Cu-Cu, and C-Cu atoms are, respectively, determined by three potential functions: AIREBO, EAM, and LJ. The effect of the origami graphene/copper interfacial gap on the critical strain of incremental Poisson’s ratio, critical strain of engineering Poisson’s ratio, and moduli of the origami graphene/copper nanocomposites is studied to determine the optimum distance between the two phases. The influences of the mass fraction of carbon atom and temperature on those properties are discussed in detail after the MD model is confirmed.
Single-walled carbon nanotube (SWCNT) is a promising candidate for strengthening nanocomposite. As the matrix of nanocomposite, a single crystal of copper is designed to be in-plane auxetic along the crystal orientation [1 1 0]. In that way, the nanocomposite could also be auxetic when enhanced by (7, 2) a single-walled carbon nanotube with relatively small in-plane Poisson’s ratio. A series of molecular dynamics (MD) models of the nanocomposite metamaterial are then established to study mechanical behaviors of the nanocomposite. In the modelling, the gap between copper and SWCNT is determined following the principle of crystal stability. The enhanced effect for different content and temperature in different directions is discussed in detail. This study provides a complete set of mechanical parameters of nanocomposite including thermal expansion coefficients (TECs) from 300 K to 800 K for five weight fractions, which is essential for a wide range of applications of auxetic nanocomposites in the future.
2 October 2025 in Journal of Materials Chemistry A
Sulfide solid-state electrolytes are promising candidates for all-solid-state lithium metal batteries (ASSLBs) having higher energy density and practical safety due to their high ionic conductivity and favorable mechanical properties. However, their practical integration is hindered by low critical current density (CCD), a narrow electrochemical stability window, and high impedance with electrodes. Herein, we demonstrate that doping lithium phosphorus sulfide (Li7P3S11) solid electrolyte with zirconium chloride (ZrCl4) significantly enhances its electrochemical performance. Unlike previously reported doping strategies, ZrCl4 doping uniquely introduces dual dopants (Zr4+ and Cl−) into the Li7P3S11 matrix. Density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations reveal that the Zr4+ ions increase dynamic structural flexibility, while Cl− ions create additional Li+ vacancies, collectively enhancing structural stability and ionic conductivity beyond the capacity of single-element doping strategies. Optimized doping content of ZrCl4 improved the CCD of Li7P3S11 from 0.55 mA cm−2 to 1.7 mA cm−2, while the ionic conductivity improved from 1.8 × 10−3 S cm−1 to 3.0 × 10−3 S cm−1. Li/Li symmetrical cells with doped electrolyte exhibited improved cycling stability at 0.1 mA cm−2 compared to the control counterparts. Furthermore, a thin solid polymer electrolyte (SPE) was used at the interface between the cathode and solid electrolyte to enable the stack pressure free operation of full cells. Li/LiFePO4 (LFP) full cells using doped solid electrolyte (SE) in combination with SPE catholyte demonstrated stable performance compared to undoped SE based cells. The enhanced Li-dendrite suppression and improved electrochemical properties due to doped Li7P3S11 and the stack free operation due to the addition of SPE as catholyte will add significant potential for advancing ASSLB technology.