Magdalena Piechówka-Mielnik

Dr. Magdalena Piechówka-Mielnik


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Journal of Cleaner Production
Verified
Journal Article
Closed access
Łukasz SadowskiŁukasz Sadowski
Łukasz Sadowski
MPMagdalena Piechówka-Mielnik
Magdalena Piechówka-Mielnik
TWTomasz Widziszowski
Tomasz Widziszowski
AGAnna Gardynik
Anna Gardynik
SMSławomir Mackiewicz
Sławomir Mackiewicz

1 January 2021 in Science and Engineering of Composite Materials
Verified
Journal Article
Open access
PDF file
KKKamil Krzywiński
Kamil Krzywiński
Łukasz SadowskiŁukasz Sadowski
Łukasz Sadowski
MPMagdalena Piechówka-Mielnik
Magdalena Piechówka-Mielnik
The paper presents studies performed on polymer-cementitious composite made of epoxy resin coating modified with aggregate and cementitious substrate. Epoxy resin is a perfect material that can be used to protect cementitious materials. According to its manufacturer, it can be mixed with fine aggregate. Coarse aggregate made of building demolition wastes is mostly utilized in concrete mixtures or road structures. Fine aggregate is not widely used. Therefore, the novelty of this research was the utilization of recycled fine aggregate (RFA) in epoxy resin coatings. Natural fine aggregate (NFA) was also used as an extender in the coating. The natural aggregate in the coating was partially replaced with recycled aggregate in amounts of 0, 20, 40, 60, 80, and 100% of its weight. Sixteen specimens of polymer-cementitious composites were prepared for the flexural tensile strength test, and thirty-two specimens for the compressive strength test. The macroscale tests were performed after 35 days of curing (28 days – cementitious substrate, and 7 days – epoxy resin). The results show that the epoxy resin coating does not affect the flexural tensile and compressive strength of the analyzed composites. Moreover, the type of aggregate used in the coating does not have a significant impact on the measured properties of polymer-cementitious composites. Economic analysis was performed in order to estimate the cost of the natural and RFAs used in epoxy resin coatings. The calculations show that a higher amount of RFA should be used to increase savings.

19 January 2020 in Coatings
Verified
Journal Article
Open access
PDF file
KKKamil Krzywiński
Kamil Krzywiński
Łukasz SadowskiŁukasz Sadowski
Łukasz Sadowski
JSJacek Szymanowski
Jacek Szymanowski
Andrzej ZakAndrzej Zak
Andrzej Zak
MPMagdalena Piechówka-Mielnik
Magdalena Piechówka-Mielnik
This article presents studies that were performed in order to improve the subsurface properties of horizontally-formed cementitious composites using tin(II) fluoride nanoparticles. The main aim of the study was to solve the problem of the decrease in subsurface properties caused by mortar bleeding and the segregation of the aggregate along the height of the overlay. The article also aims to highlight the patch grabbing difficulties that occur during the process of forming horizontally-formed cementitious composites. Four specimens were analyzed: one reference sample and three samples modified with the addition of 0.5, 1.0, and 1.5% of tin(II) fluoride nanoparticles in relation to the cement mass. To analyze the mechanical properties of the specimens, non-destructive (ultrasonic pulse velocity) and destructive tests (flexural tensile strength, compressive strength, abrasion resistance, pull-off strength) were performed. It was indicated that due to the addition of the tin(II) fluoride, it was possible to enhance the subsurface tensile strength and abrasion resistance of the tested cementitious composites. To confirm the obtained macroscopic results, the porosity of the subsurface was measured using SEM. It was also shown that the addition of the tin(II) fluoride nanoparticles did not reduce its flexural and compressive strength. The results show that horizontally-formed cementitious composites with the addition of 1.0% of tin(II) fluoride nanoparticles in relation to the cement mass obtained the most effective mechanical performance, especially with regard to subsurface properties.

6 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
KAKrzysztof Ałykow
Krzysztof Ałykow
Lukasz Jan BednarzLukasz Jan Bednarz
Lukasz Jan Bednarz
MPMagdalena Piechówka-Mielnik
Magdalena Piechówka-Mielnik
MNMagdalena Napiórkowska-Ałykow
Magdalena Napiórkowska-Ałykow
MKMichał Krupa
Michał Krupa
In the case of historic buildings, especially those under protection, it is important to replace elements of the roof covering, while maintaining current technical standards, to meet the requirements of the conservator. The authors of the article present alternatives to commonly used solutions, based on their experience with replacing historic building roofing with ceramic tiles made according to the production and firing technology of the nineteenth century. They emphasize that the correct/specialized restoration of existing tiles in a building makes it possible to preserve and reuse them, which is in line with the principles of historic preservation. However, due to the preservation of the roof tiles, it is not always possible to revitalize them. As a solution to the problem, the use of clay roof tiles manufactured according to 19th-century firing technology, including handmade methods, is presented, which preserves the geometry of the historic roof tiles. The approach presented by the authors meets both the requirements of conservation theory and the building standards for roofing elements. Although it is much more expensive than the solutions currently commonly used that result from modern technical requirements and tile-manufacturing technology, in the case of objects of significant cultural heritage, it is a solution that meets modern technical requirements while not compromising the original appearance of the monument.

23 September 2025 in MATERIAŁY BUDOWLANE
Verified
Journal Article
Closed access
MPMagdalena Piechówka-Mielnik
Magdalena Piechówka-Mielnik
Lukasz Jan BednarzLukasz Jan Bednarz
Lukasz Jan Bednarz
MKMichał Krupa
Michał Krupa
GWGabriela Wojciechowska
Gabriela Wojciechowska
NDNoëlla Dolińska
Noëlla Dolińska
W artykule przedstawiono zastosowanie technologii druku 3D betonu i zbrojenia mieszanek włóknami konopnymi. Omówiono wymagania dotyczące betonów do druku 3D, właściwości włókien oraz ich wpływ na reologię i parametry mechaniczne mieszanek, a także wyniki badań mieszanek cementowych z dodatkiem włókien, uwzględniając wpływ współczynnika w/c na konsystencję i jakość wydruku. Połączenie druku 3D z naturalnymi włóknami wspiera zrównoważone budownictwo.