Andreas Bengtsson

Mr. Andreas Bengtsson

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 April 2019 in ACS Sustainable Chemistry & Engineering
Verified
Journal Article
Open access
ABAndreas Bengtsson
Andreas Bengtsson
JBJenny Bengtsson
Jenny Bengtsson
MSMaria Sedin
Maria Sedin
ESElisabeth Sjöholm
Elisabeth Sjöholm
There is an increasing demand for lightweight composites reinforced with carbon fibers (CFs). Due to its high availability and carbon content, kraft lignin has gained attention as a potential low-cost CF precursor. CFs with promising properties can be made from flexible dry-jet wet spun precursor fibers (PFs) from blends (70:30) of softwood kraft lignin and fully bleached softwood kraft pulp. This study focused on reducing the stabilization time, which is critical in CF manufacturing. The impact of stabilization conditions on chemical structure, yield, and mechanical properties was investigated. It was possible to reduce the oxidative stabilization time of the PFs from about 16 h to less than 2 h, or even omitting the stabilization step, without fusion of fibers. The main reactions involved in the stabilization stage were dehydration and oxidation. The results suggest that the isothermal stabilization at 250 °C override the importance of having a slow heating rate. For CFs with a commercial diameter, stabilization of less than 2 h rendered in tensile modulus 76 GPa and tensile strength 1070 MPa. Impregnation with ammonium dihydrogen phosphate significantly increased the CF yield, from 31–38 to 46–50 wt %, but at the expense of the mechanical properties.

15 April 2020 in ACS Sustainable Chemistry & Engineering
Verified
Journal Article
Closed access
ABAndreas Bengtsson
Andreas Bengtsson
PHPascale Hecht
Pascale Hecht
JSJens Sommertune
Jens Sommertune
MEMonica Ek
Monica Ek
MSMaria Sedin
Maria Sedin
ESElisabeth Sjöholm
Elisabeth Sjöholm

5 May 2022 in ACS Omega
Verified
Journal Article
Open access
ABAndreas Bengtsson
Andreas Bengtsson
JBJenny Bengtsson
Jenny Bengtsson
KJKerstin Jedvert
Kerstin Jedvert
MKMarkus Kakkonen
Markus Kakkonen
OTOlli Tanhuanpää
Olli Tanhuanpää
MSMaria Sedin
Maria Sedin
The demand for carbon fibers (CFs) based on renewable raw materials as the reinforcing fiber in composites for lightweight applications is growing. Lignin-cellulose precursor fibers (PFs) are a promising alternative, but so far, there is limited knowledge of how to continuously convert these PFs under industrial-like conditions into CFs. Continuous conversion is vital for the industrial production of CFs. In this work, we have compared the continuous conversion of lignin-cellulose PFs (50 wt % softwood kraft lignin and 50 wt % dissolving-grade kraft pulp) with batchwise conversion. The PFs were successfully stabilized and carbonized continuously over a total time of 1.0-1.5 h, comparable to the industrial production of CFs from polyacrylonitrile. CFs derived continuously at 1000 °C with a relative stretch of -10% (fiber contraction) had a conversion yield of 29 wt %, a diameter of 12-15 μm, a Young's modulus of 46-51 GPa, and a tensile strength of 710-920 MPa. In comparison, CFs obtained at 1000 °C via batchwise conversion (12-15 μm diameter) with a relative stretch of 0% and a conversion time of 7 h (due to the low heating and cooling rates) had a higher conversion yield of 34 wt %, a higher Young's modulus (63-67 GPa) but a similar tensile strength (800-920 MPa). This suggests that the Young's modulus can be improved by the optimization of the fiber tension, residence time, and temperature profile during continuous conversion, while a higher tensile strength can be achieved by reducing the fiber diameter as it minimizes the risk of critical defects.

15 December 2022 in Fibers
Verified
Journal Article
Open access
PDF file
ABAndreas Bengtsson
Andreas Bengtsson
ALAlice Landmér
Alice Landmér
LNLars Norberg
Lars Norberg
SYShun Yu
Shun Yu
MEMonica Ek
Monica Ek
MSMaria Sedin
Maria Sedin
In recent years, there has been extensive research into the development of cheaper and more sustainable carbon fiber (CF) precursors, and air-gap-spun cellulose-lignin precursors have gained considerable attention where ionic liquids have been used for the co-dissolution of cellulose and lignin. However, ionic liquids are expensive and difficult to recycle. In the present work, an aqueous solvent system, cold alkali, was used to prepare cellulose-lignin CF precursors by wet spinning solutions containing co-dissolved dissolving-grade kraft pulp and softwood kraft lignin. Precursors containing up to 30 wt% lignin were successfully spun using two different coagulation bath compositions, where one of them introduced a flame retardant into the precursor to increase the CF conversion yield. The precursors were converted to CFs via batchwise and continuous conversion. The precursor and conversion conditions had a significant effect on the conversion yield (12–44 wt%), the Young’s modulus (33–77 GPa), and the tensile strength (0.48–1.17 GPa), while the precursor morphology was preserved. Structural characterization of the precursors and CFs showed that a more oriented and crystalline precursor gave a more ordered CF structure with higher tensile properties. The continuous conversion trials highlighted the importance of tension control to increase the mechanical properties of the CFs.