The disc-cutter is a finishing tool for the ultrasonic-cutting of paper honeycomb-core material. The cutting state directly affects the machining accuracy and surface quality of the workpiece. The cutting force is an important physical quantity and the cause of ultrasonic cutting defects of the honeycomb-core material. Due to differences in the mechanical properties and cutting performance of honeycomb-core materials and commonly used metal materials, existing metal-cutting-force models cannot be applied to the calculation of ultrasonic cutting forces in the processing of honeycomb-core materials. In response to this problem—combined with actual working conditions using the ABAQUS finite element analysis software—a finite element simulation model of the ultrasonic vibration-assisted cutting force of the disc-cutter on the honeycomb-core material was established, and the cutting curves and values were obtained. The experiment of ultrasonic vibration cutting of the disc-cutter proves that from the surface morphology of the honeycomb core, the milling-width has the greatest influence on the cutting force, and the cutting-depth has the smallest influence on the cutting force. The maximum error between the cutting force experimental results and the finite element simulation results under the same cutting conditions was 13.2%, which means that the established cutting-force finite element model is more accurate and can be used to predict the cutting in honeycomb ultrasonic vibration-assisted cutting-force value. Finally, based on the response surface method, a three-dimensional cutting force prediction model of the ultrasonic cutting honeycomb core of the disc-cutter was established by using the simulation model data. The results of this study can provide a useful basis for the improvement of cutting performance and processing efficiency in the processing of paper honeycomb-core materials.

According to the increasing needs of rotary table and spindle to satisfy high-precision machining requirements, the accuracy of rotary table and spindle becomes an important issue due to the error averaging effect of hydrostatic thrust bearing. The objective of this study is to research a methodology to guide the precision design of hydrostatic thrust bearing in rotary table and spindle. A run-out error model based on error averaging effect is established using the Reynolds equation, pressure boundary conditions, flux continuity equations of pad and dynamic equations of shaft. The axial run-out error and angular error are calculated considering perpendicularity error and flatness error of the components. The simulation results show that the two perpendicularity errors between axis line and thrust bearing bushing surface have same direction, and the axial run-out error could reach to the maximum values. Also, the flatness error of thrust bearing bushing surface has a big influence on axial run-out error. Following the outcomes, the precision design of hydrostatic thrust bearing was conducted. The axial run-out errors of rotary table and spindle with hydrostatic thrust bearing were experimentally studied, and the results have good coherence to the simulation data. The run-out error model is demonstrated to be an effective approach to guide the precision design of hydrostatic thrust bearing in other rotary tables and spindles.

Deformation of thin-walled titanium alloys can occur during the milling process due to the cutting force and chatter vibration, which can influence the precision of the finished parts. In this research, a new milling method without auxiliary support for machining of thin-walled parts was proposed. A large cutting depth and layered milling technology were used during rough machining, with a different machining allowance for each subsequent remaining layer. In the finishing stage, the surface of the previous layer needed to be dressed before processing the next layer. A TiAlSiN-coated, cemented carbide milling cutter was used to machine titanium alloy thin-walled parts, which are characterized by continuous multilayers of unequal thickness. The processing path was simulated using HyperMILL software, and the machining accuracy was detected by the 3D optical scanner. The measurement results indicated that the surface contour accuracy of the parts was ±0.21 mm, within a range of ±0.30 mm. The machining efficiency was increased by 40%, while guaranteeing machining accuracy.

Improving the cutting efficiency is the major factor for improving the processing of nickel-based alloys. The novelty of this research is the calibrated SiAlON ceramic tool dry milling nickel-based alloy process. Firstly, the nickel-based alloy dry milling process was analyzed through the finite element method, and the required milling force and temperature were deduced. Then, several dry milling experiments were conducted with the milling temperature, and the milling force was monitored. The change in cutting speeds was from 400 m/min to 700 m/min. Experimental results verified the reduction of the dry milling force hypothesized by the simulation. The experiment also indicated that with a cut depth of 0.3 mm, cut width of 6 mm, and feed per tooth of 0.03 mm/z, when milling speed exceeded 527.52 m/min, the milling force began to decrease, and the milling temperature exceeded the nickel-based alloy softening temperature. This indicated that easy cutting could be realized under high-speed dry milling conditions. The interpolation curve about average temperature and average milling forces showed similarity to the tensile strength reduction with the rise of temperature.