Laboratory experiments are carried out to detect optical vortices in conditions typical of those experienced when a laser beam is propagated through the atmosphere. A Spatial Light Modulator (SLM) is used to mimic atmospheric turbulence and a Shack-Hartmann wavefront sensor is utilised to measure the slopes of the wavefront surface. A matched filter algorithm determines the positions of the Shack-Hartmann spot centroids more robustly than a centroiding algorithm. The slope discrepancy is then obtained by taking the slopes measured by the wavefront sensor away from the slopes calculated from a least squares reconstruction of the phase. The slope discrepancy field is used as an input to the branch point potential method to find if a vortex is present, and if so to give its position and sign. The use of the slope discrepancy technique greatly improves the detection rate of the branch point potential method. This work shows the first time the branch point potential method has been used to detect optical vortices in an experimental setup.

In this paper we compare experimentally two methods of detecting optical vortices from Shack-Hartmann wavefront sensor (SHWFS) data, the vortex potential and the contour sum methods. The experimental setup uses a spatial light modulator (SLM) to generate turbulent fields with vortices. In the experiment, many fields are generated and detected by a SHWFS, and data is analysed by the two vortex detection methods. We conclude that the vortex potential method is more successful in locating vortices in these fields.

A method for fabricating diffractive holographic optical diffusers is reported, allowing a high degree of control of the resulting diffuser characteristics. The method consists of recording a laser speckle pattern using a single carrier beam, with controlled speckle size and shape, in an acrylamide-based volume photopolymer. The multiple interferences that create the speckle pattern form the hologram. Results are presented verifying the diffusers are volume holographic in nature and the speckle pattern is recorded accurately in the photopolymer. Diffusers recorded by this method are analysed to characterise the optical performance of the diffusers and to illustrate their beam-shaping capabilities, particularly in producing asymmetric beam outputs.

A holographic optical element (HOE) was developed to collimate a monochromatic light-emitting diode (LED). The fabrication was achieved by the interference of collimated and diverging beams from a 532 nm laser to produce the required photonic structure in a self-developing photopolymer material. The experimental values of diffraction efficiency and spatial period across the HOE were compared with their expected theoretical values. Good agreement was found for the spatial period; however, the diffraction efficiency varied significantly across the lens. In this paper, two approaches have been taken to address this variation: (1) modification of recording geometry and (2) optimization of recording intensity and exposure time at constant energy. The performance of an optimized HOE (cylindrical holographic lens) was then demonstrated using a 532 nm laser beam. The optimized conditions for the cylindrical holographic lens were used to fabricate a spherical holographic lens of the same numerical aperture for LED applications. This type of lens has the potential to be used in combination with LED sources.

A novel stacking procedure is presented for volume phase holographic gratings (VPHGs) recorded in photopolymer material using Corning Willow Glass as a flexible substrate in order to achieve broader angular and spectral selectivity in a diffractive device with high efficiency for solar and LED applications. For the first time to our knowledge, we have shown a device designed for use with a white LED that has the same input and output angles and high efficiency when illuminated by different wavelengths. In this paper, two VPHGs were designed, experimentally recorded, and tested when illuminated at normal incidence. The experimental approach is based on stacking two individual gratings in which the spatial frequency and slant have been tailored to the target wavelength and using real-time on-Bragg monitoring of the gratings in order to control the recorded refractive index modulation, thereby optimizing each grating efficiency for its design wavelength. Lamination of the two gratings together was enabled by using a flexible glass substrate (Corning Willow Glass). Recording conditions were studied in order to minimize the change in diffraction efficiency and peak diffraction angle during lamination and bleaching. The final fabricated stacked device was illuminated by a white light source, and its output was spectrally analyzed. Compared to a single grating, the stacked device demonstrated a twofold increase in angular and wavelength range. The angular and wavelength selectivity curves are in good agreement with the theoretical prediction for this design. This approach could be used to fabricate stacked lenses for white light LED or solar applications.