Liyan Zhu

Dr. Liyan Zhu

Center for Power Electronics Systems (CPES), Virginia Tech, VA, USA
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 June 2016 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SLSiqi Li
Siqi Li
ZLZhe Liu
Zhe Liu
HZHan Zhao
Han Zhao
Liyan ZhuLiyan Zhu
Liyan Zhu
CSChunyan Shuai
Chunyan Shuai
ZCZheng Chen
Zheng Chen
In this paper, the electric field resonance (EFR) method, similar to the four-coil configuration of the magnetic field resonance wireless power transfer, is proposed for the capacitive coupling power transfer. The characteristics of the proposed method are derived and analyzed. With the EFR method, not only unity power factor for the power source is achieved, but also high power factor and low reactive power for the capacitive coupling stage are achieved. Effective power transfer is realized by the EFR method. Based on the proposed method, a dynamic charging concept for railway vehicles is then proposed. A prototype powering system is designed and built to prove the validity of the proposed method. Analytical, simulation, and experimental results are given and compared. A 23-cm model vehicle is put on a 150-cm track. It is shown that about 700-W power is transferred through a 24-pF coupling capacitor. The proposed method reaches 91% dc–dc overall efficiency at switching frequency 2 MHz.

31 January 2024 in IEEE Open Journal of Power Electronics
Verified
Journal Article
Open access
XYXipei Yu
Xipei Yu
JFJunjie Feng
Junjie Feng
Liyan ZhuLiyan Zhu
Liyan Zhu
QLQiang Li
Qiang Li
Recently, omnidirectional wireless power transfer (WPT) has gained increasing popularity due to its capability to charge in arbitrary positions and directions. However, existing solutions still face several challenges, including coupled coils, non-optimized structure, non-uniform magnetic field, and poor misalignment tolerance. This work proposed an omnidirectional WPT system with three fully decoupled coils consisting of one square coil and two perpendicular DD coils. Comprehensive modeling and Pareto optimization for the transmitter coil structure are conducted for improved tolerance to both lateral and angular misalignment. Experimental results are provided to validate the system performance in terms of the output voltage and efficiency under different lateral and angular misalignments. With a 12 V input, the efficiency of the system exhibits a <10% variation, ranging from 69% to 78%, with 50mm misalignment in the x and y axes and a 90-degree angular misalignment. At the same time, the output voltage remains within the range of 11.5 V to 14.5 V.

7 August 2018 in IET Power Electronics
Verified
Journal Article
Open access
PDF file
ATAllan Taylor
Allan Taylor
JLJuncheng Lu
Juncheng Lu
Liyan ZhuLiyan Zhu
Liyan Zhu
KBKevin (Hua) Bai
Kevin (Hua) Bai
MMMatt McAmmond
Matt McAmmond
ABAlan Brown
Alan Brown
As two exemplary candidates of wide‐bandgap devices, SiC MOSFETs and GaN HEMTs are regarded as successors of Si devices in medium‐to‐high‐voltage (>1200 V) and low‐voltage (<650 V) domains, respectively, thanks to their excellent switching performance and thermal capability. With the introduction of 650 V SiC MOSFETs and GaN HEMTs, the two technologies are in direct competition in <650 V domains, such as Level 2 battery chargers for electric vehicles (EVs). This study applies 650 V SiC and GaN to two 240 VAC/7.2 kW EV battery chargers, respectively, aiming to provide a head‐to‐head comparison of these two devices in terms of overall efficiency, power density, thermal performance, and cost. The charger essentially is an indirect matrix converter with a dual‐active‐bridge stage handling the power factor correction and power delivery simultaneously. These two chargers utilise the same control strategy, varying the phase‐shift and switching frequency to cover the wide input range (80–260 VAC) and wide output range (200 V–450 VDC). Experimental results indicated that at the same efficiency level, the GaN charger is smaller, more efficient and cheaper, while the SiC charger has a better thermal performance.

20 November 2023 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
ZLZiwei Liang
Ziwei Liang
Liyan ZhuLiyan Zhu
Liyan Zhu
YSYue Sun
Yue Sun
JLJie Li
Jie Li
RQRuiyang Qin
Ruiyang Qin
HBHua Bai
Hua Bai
To further improve the system integration and convenience of the battery charging system for electric vehicles, this letter proposed a multipurpose magnetic coupler-based charging solution that integrates bidirectional on-board charger (OBC), wireless power transfer (WPT), and an auxiliary power module (APM). The proposed solution presents multiple highlights: 1) the first exhibited solution to integrate OBC, WPT, and APM in one unit; 2) magnetic integration that uses a multiwinding WPT pad to eliminate the main transformer of OBC and APM; and 3) topological integration that saves multiple active and passive devices. This letter includes a description of the system topology, operation principles of individual charging modes, a novel magnetic coupler, and the design methodology. Finally, a prototype was constructed and different charging modes were tested to validate the proposed design.

1 October 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Liyan ZhuLiyan Zhu
Liyan Zhu
HBHua Bai
Hua Bai
ABAlan Brown
Alan Brown
MMMatt McAmmond
Matt McAmmond
An auxiliary power module (APM) in electric vehicles is a DC/DC converter bridging the high voltage propulsion battery with a low voltage auxiliary system. With the era of connected and autonomous vehicles coming, the power rating of such DC/DC is expected to surge, say from 2.5kW to 6kW. No mention its challenge of wide operating voltage range, e.g., 250~450V input provided by the high voltage propulsion battery and 10~16V at the low voltage auxiliary battery. To meet such voltage and power challenges, this paper proposed a two-stage bidirectional design, i.e., interleaved buck + DC transformer (DCX) offering full voltage range coverage, 3.5kW rated power and peak power of >6kW. Experimental results indicated >96% efficiency, thanks to the zero-switching loss of DCX. In addition, the pre-charge mode to charge the input DC bus capacitor with the low-voltage battery is also achieved using the inner phase shift control at the DCX stage. To save DC-bias blocking capacitors at the low-voltage side, a novel and simple DC bias detection circuit is proposed to sample the DC-current offset of the transformer. Both simulation and test results verified that the proposed method can effectively detect and eliminate the DC bias current.

28 March 2018 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
Liyan ZhuLiyan Zhu
Liyan Zhu
Allan Ray TaylorAllan Ray Taylor
Allan Ray Taylor
GLGuanliang Liu
Guanliang Liu
KBKevin Bai
Kevin Bai
An ac/dc + dual-active-bridge (DAB) circuit was found as one solution for the high-efficiency and high-power-density electric vehicle charger. One control option is to let ac/dc part only convert the grid voltage to a double-line-frequency folded sine wave, yielding near-zero switching loss of the ac/dc part and leaving the DAB stage to control both power factor and power delivery. Such a zero-to-peak input voltage and wide-range output voltage can obstruct the zero-voltage switching (ZVS) for the DAB stage, which is a must for high-efficiency applications even with SiC devices. While the conventional single-phase shift loses ZVS at light load, and the variable-switching-frequency dual phase shift (DPS) creates the grid-current distortion at the light load, this paper employs multiple-phase-shifts (MPS) control, which essentially is a fixed-switching-frequency triple-phase-shift (TPS) control at light-load conditions and jumping to DPS at medium- and heavy-load conditions. While the TPS control will sacrifice the system efficiency by introducing the circulating current, a multiobjective optimization is employed to optimize the current stress and efficiency simultaneously, using the database of the double-pulse-test result. Experimental results on a SiC-based charger validated the effectiveness of the proposed control algorithm, that is: 1) high efficiency(>97%) at heavy load (7.2 kW); 2) smooth sinusoidal current without bumps at zero-crossing points from the whole-load range; and 3) the smooth transition between the heavy load and light load.