Radoslaw Przysowa

Dr. Radoslaw Przysowa

Instytut Techniczny Wojsk Lotniczych (ITWL), ul. Księcia Bolesława 6, 01-494 Warszawa, Poland
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 January 2021 in Aerospace
Verified
Journal Article
Open access
PDF file
RPRadoslaw Przysowa
Radoslaw Przysowa
BGBartosz Gawron
Bartosz Gawron
TBTomasz Białecki
Tomasz Białecki
AŁAnna Łęgowik
Anna Łęgowik
JMJerzy Merkisz
Jerzy Merkisz
Remigiusz JasińskiRemigiusz Jasiński
Remigiusz Jasiński
Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines—the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: (1) Alcohol-to-Jet (ATJ) and (2) Hydroprocessed Esters and Fatty Acids (HEFA) produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

22 December 2020 in Aerospace
Verified
Journal Article
Open access
PDF file
DPDmytro Pavlenko
Dmytro Pavlenko
YDYaroslav Dvirnyk
Yaroslav Dvirnyk
RPRadoslaw Przysowa
Radoslaw Przysowa
Manufacturing costs, along with operational performance, are among the major factors determining the selection of the propulsion system for unmanned aerial vehicles (UAVs), especially for aerial targets and cruise missiles. In this paper, the design requirements and operating parameters of small turbofan engines for single-use and reusable UAVs are analysed to introduce alternative materials and technologies for manufacturing their compressor blades, such as sintered titanium, a new generation of aluminium alloys and titanium aluminides. To assess the influence of severe plastic deformation (SPD) on the hardening efficiency of the proposed materials, the alloys with the coarse-grained and submicrocrystalline structure were studied. Changes in the physical and mechanical properties of materials were taken into account. The thermodynamic analysis of the compressor was performed in a finite element analysis system (ANSYS) to determine the impact of gas pressure and temperature on the aerodynamic surfaces of compressor blades of all stages. Based on thermal and structural analysis, the stress and temperature maps on compressor blades and vanes were obtained, taking into account the physical and mechanical properties of advanced materials and technologies of their processing. The safety factors of the components were established based on the assessment of their stress-strength characteristics. Thanks to nomograms, the possibility of using the new materials in five compressor stages was confirmed in view of the permissible operating temperature and safety factor. The proposed alternative materials for compressor blades and vanes meet the design requirements of the turbofan at lower manufacturing costs.

25 January 2022 in Engineering Failure Analysis
Verified
Journal Article
Open access
ASAndrzej Szczepankowski
Andrzej Szczepankowski
RPRadoslaw Przysowa
Radoslaw Przysowa

21 December 2019 in Sensors
Verified
Journal Article
Open access
PDF file
RPRadoslaw Przysowa
Radoslaw Przysowa
PRPeter Russhard
Peter Russhard
Complex blade responses such as a rotating stall or simultaneous resonances are common in modern engines and their observation can be a challenge even for state-of-the-art tip-timing systems and trained operators. This paper analyses forced vibrations of axial compressor blades, measured during the bench tests of the SO-3 turbojet. In relation to earlier studies conducted in Poland with a small number of sensors, a multichannel tip-timing system let us observe simultaneous responses or higher-order modes. To find possible symptoms of a failure, blade responses in a healthy and unhealthy engine configuration with an inlet blocker were studied. The used analysis methods covered all-blade spectrum and the circumferential fitting of blade deflections to the harmonic oscillator model. The Pearson coefficient of correlation between the measured and predicted tip deflection is calculated to evaluate fitting results. It helps to avoid common operator mistakes and misinterpreting the results. The proposed modal solver can track the vibration frequency and adjust the engine order on the fly. That way, synchronous and asynchronous vibrations are observed and analysed together with an extended variant of least squares. This approach saves a lot of work related to configuring the conventional tip-timing solver.

24 January 2022 in Aerospace
Verified
Journal Article
Open access
PDF file
MEMario Erario
Mario Erario
Maria Grazia De GiorgiMaria Grazia De Giorgi
Maria Grazia De Giorgi
RPRadoslaw Przysowa
Radoslaw Przysowa
Microturbines can be used not only in models and education but also to propel UAVs. However, their wider adoption is limited by their relatively low efficiency and durability. Validated simulation models are required to monitor their performance, improve their lifetime, and to design engine control systems. This study aims at developing a numerical model of a micro gas turbine intended for prediction and prognostics of engine performance. To build a reliable zero-dimensional model, the available compressor and turbine maps were scaled to the available test bench data with the least squares method, to meet the performance of the engine achieved during bench and flight tests. A steady-state aeroengine model was implemented in the Gas turbine Simulation Program (GSP) and was compared with experimental operating points. The selected flight data were then used as input for the transient engine model. The exhaust gas temperature (EGT) and fuel flow were chosen as the two key parameters to validate the model, comparing the numerical predicted values with the experimental ones. The observed difference between the model and the flight data was lower than 3% for both EGT and fuel flow.

11 November 2016 in Sensors
Verified
Journal Article
Open access
PDF file
IGIker García
Iker García
RPRadoslaw Przysowa
Radoslaw Przysowa
JAJosu Amorebieta
Josu Amorebieta
Joseba Zubia ZaballaJoseba Zubia Zaballa
Joseba Zubia Zaballa
In this article, we report the design of a reflective intensity-modulated optical fiber sensor for blade tip-clearance measurement, and the experimental results for the first stage of a compressor of an aircraft engine operating in real conditions. The tests were performed in a ground test cell, where the engine completed four cycles from idling state to takeoff and back to idling state. During these tests, the rotational speed of the compressor ranged between 7000 and 15,600 rpm. The main component of the sensor is a tetrafurcated bundle of optical fibers, with which the resulting precision of the experimental measurements was 12 µm for a measurement range from 2 to 4 mm. To get this precision the effect of temperature on the optoelectronic components of the sensor was compensated by calibrating the sensor in a climate chamber. A custom-designed MATLAB program was employed to simulate the behavior of the sensor prior to its manufacture.