The paper shows the results of the truck driveline dynamic loading processes made with an imitation modeling approach. The developed mathematical model of a vehicle motion includes the functioning features of all principal automotive mechanical systems and units. We considered one of the most difficult driving conditions, when the potential necessity of interaxial differential locking arises. The loads acting in transmission at the differential locking unit engagement were estimated.
14 April 2015 in SAE International Journal of Advances and Current Practices in Mobility
The main indicators for mobility of a multipurpose wheeled vehicle (MWV) are the maximum and average technical velocity, and they are mainly determined by power-to-weight ratio and parameters of the suspension. As our analysis shows, with the increase of the power-to-weight ratio of the vehicle and its weight, the growth rate of the velocity is reduced, and after reaching a certain value, the velocity remains almost constant. This is due to the fact that for operating conditions of the multipurpose wheeled vehicle, movement on roads with different degrees of uneven distribution of the rolling resistance and tire traction, in both transverse and longitudinal directions, is typical.In this investigation we evaluate the effectiveness of the main methods of power distribution between the drive wheels of the multipurpose wheeled vehicles: disabling of drive axles, blocking of cross-axle and inter-axle differentials, a slowdown of slipping wheels.It was revealed that the transmission of a promising MWV has to be modernized in the following ways: 1) all-wheel drive with the rational value of the gear ratio of inter-axle differential (by a “rational gear ratio” here and further in this paper we mean the selection of the gear ratio by fitting a number of teeth of gears in inter-axle differential); 2) realization of the possibility of periodic shutdown of the drive axles when road conditions are good, or turning on the additional driving axles of the trailer when the road conditions require significant drive forces and torques; 3) providing of limited excess capacity of power unit by reducing the fuel supply or applying braking torque to the slipping wheels; 4) providing of rigid kinematic connection in the movement process with compensation of the kinematic mismatch by adjusting of air pressure in the tires.At present, the effectiveness of the proposed methods of power distribution has been investigated in different extent. Thus, there arises the problem of the complex evaluation of the effectiveness of methods of the power distribution between the drive wheels of the multi-purpose wheeled vehicle. This investigation is devoted to this problem.
29 September 2015 in SAE International Journal of Advances and Current Practices in Mobility
The main indicators for mobility of a multipurpose wheeled vehicle are the maximum and average technical velocity, and they are mainly determined by power-to-weight ratio and the parameters of the suspension. As our analysis shows, with the increase of the power-to-weight ratio of the vehicle and its weight, the growth rate of the velocity is reduced, and after reaching a certain value, the velocity remains almost constant. This is due to the fact that for operating conditions of the multi-purpose wheeled vehicle, movement on roads with different degrees of uneven distribution of the rolling resistance and adhesion, in both transverse and longitudinal directions, is typical.In this investigation we evaluate the effectiveness of the main methods of power distribution among drive wheels of the multi-purpose wheeled vehicles. It was revealed that the transmission of a promising multipurpose wheeled vehicle has to be modernized in the following ways: 1) all-wheel drive with the rational value of the gear ratio of inter-axle differential; 2) realization of the possibility of periodic shutdown of the drive axles when road conditions are good, or turning on the additional driving axles of the trailer when the road conditions require significant drive forces and torques; 3) providing of limited excess capacity of power unit by reducing the fuel supply or applying braking torque to the slipping wheels; 4) providing of rigid kinematic connection in the movement process with compensation of the kinematic mismatch by adjusting of air pressure in the tires.At present, the effectiveness of the proposed methods of power distribution has been investigated in different extent. Thus, there arises the problem of the complex evaluation of the effectiveness of methods of the power distribution between the drive wheels of the multi-purpose wheeled vehicle. This investigation is devoted to this problem.
27 September 2016 in SAE International Journal of Advances and Current Practices in Mobility
In this paper we consider a new design of adaptive suspension systems of vehicles with better technical characteristics and functional abilities in comparison with existing designs. We have developed the following main suspension components of vehicles: a lockable adaptive shock absorber with a wide range of control performance, implementing "lockout" mode by means of blocking adaptive shock absorber, and an elastic element with progressive non-linear characteristic and automatic optimization of localization of work areas. Advantages of our developments in the vehicle suspensions are the following: 1) when the vehicle is in a wide range of speeds in a so-called "comfort zone", we have managed, by applying the non-linear elastic element, to reduce significantly the stiffness of the elastic suspension elements in compare with the regular structures - at least in two times. This means that comfort, smooth motion, high performance the vehicle when driving over bumps are improved in times. Dynamic loads on the crew, passengers, equipment, components and assemblies of the vehicles are reduced in a big extent; 2) stiffness of the non-linear elastic element beyond "comfort zone" is increasing: at first - more than three times as compared with regular elastic elements; and further increasing of the stiffness of the elastic elements is more than 60 times. We have installed the developed design of the suspension on the Russian cars VAZ "LADA-GRANTA" and "LADA-KALINA." In this paper we describe some results of experimental studies. The experimental results confirmed the validity of the theoretical propositions.
29 September 2015 in SAE International Journal of Advances and Current Practices in Mobility
The problem of the theory of power transmission to wheels of a vehicle, as part of the theory of cars, has always been in the center of attention of specialists. With the improvement of designs of a vehicle there was a need of thorough scientific review of theoretical and experimental aspects of creating and applying of mechanical, hydrostatic, electrical, and combined transmissions. This has always remained one of the most important questions of the rational allocation of power among drive wheels.In the present paper, it has been done study of different methods of power distribution among the drive wheels of an all-wheel-drive truck, namely: method of partial solution; method of introducing a rigid kinematic connection; method of periodical action; and method of limit of excessive action. Assessment how these methods influence on the performance characteristics of a multi-purpose vehicle has been done.For implementation of the method of partial solution it has been developed method of measuring of rational gear ratio of center differential providing the required level of performance of the all-wheel drive truck. For implementation of the method of periodical action the appropriateness of switching off some of the driving axles is justified. Assessment of the effectiveness of the method of limit of excessive action by applying a braking torque to the slipping wheels has showed that the degree of braking is limited, on the one hand, by exception of slipping of the wheels on the surface with worse traction, and, on the other hand, by providing sustainable drive of the all-wheel-drive truck. Using the method of limit of excessive action by controlling engine torque with simultaneous introduction of rigid kinematic connection is the best way to increase the mobility of all-wheel-drive trucks in conditions of compacted and loose soils. The made studies that are described in this paper will help designers to find the best way for design a system of power distribution in transmissions of all-wheel-drive trucks.
29 September 2015 in SAE International Journal of Advances and Current Practices in Mobility
This paper is devoted to development of methodology of system analysis of power distribution systems and methods of synthesis of objective laws in the power distribution among drive wheels of a multipurpose wheel vehicle.The methodology of system analysis provides for formulation of the problem; structural analysis of power distribution systems; the synthesis of objective laws in the power distribution; development of methods for their implementation. The methodology is based on the theory of the synthesis of technical systems. In this paper parameters of characteristics of control actions have been determined in accordance with specified requirements to effectiveness of the multipurpose wheeled vehicle expressed in the form of formulated performance criteria. The main stages of the methodology for determining of the objective laws of the power distribution among the drive wheels of a vehicle are: formulation of the optimization problem; computational procedure and definition of the basic laws of the power distribution; adaptation of the basic laws, and assessment of the effectiveness of proposed solutions.We have developed a new principle of power distribution, providing the required level of mobility of the multipurpose wheeled vehicle. Application of the methodology of system analysis allows us to improve the quality of design of the systems of power distribution among drive wheels and to design multi-purpose wheeled vehicles with optimal parameters.