Polymer flooding has drawn more and more attention in the world for its high incremental oil recovery factor and relative low costs compared with water flooding and other chemically enhanced oil recovery techniques. However, for many oilfields, such as Daqing Oilfield, China, that have already been flooded with polymers, how to further improve recovery remains a big problem. Traditional intralayer, interlayer and plane heterogeneity studies cannot accurately characterize the remaining oil distribution after polymer flooding. To solve this problem, we established a method to quantitatively describe the reservoir’s architecture. Then, the architecture elements were dissected hierarchically and the interface of each architecture level in Daqing Oilfield was identified. The distribution pattern and development potential of the remaining oil after polymer flooding under the influence of reservoir architecture was analyzed. The results show that, regarding the sedimentary process from north to south in Daqing Oilfield, the channel becomes narrower, the thickness decreases, the point bar’s width increases and the thickness of the meandering river decreases. The braided bar scale becomes larger and the thickness becomes smaller in the braided river. According to the reservoir’s architecture, the remaining oil was divided into four categories of plane remaining oil (abandoned channel occlusion type, interfluvial sand body occlusion type, inter-well retention type and well pattern uncontrollable type) and three types of vertical remaining oil (in-layer interlayer occlusion type, rhythm type and gravity type). About 40% of the original oil in place (OOIP) of Daqing Oilfield has not yet been produced, which indicates that there is great potential for development. This study is important for improving oil recovery in polymer-flooded reservoirs.

Foam drainage gas recovery technology is a chemical method to solve the serious bottom-hole liquid loading in the middle and late stages of gas well production, and the optimization of foam drainage agents (referred to as FDAs) is the key to the technology. According to the actual reservoir conditions, a high-temperature and high-pressure (HTHP) evaluation device for FDAs was set up in this study. The six key properties of FDAs, such as HTHP resistance, dynamic liquid carrying capacity, oil resistance, and salinity resistance, were evaluated systematically. Taking initial foaming volume, half-life, comprehensive index, and liquid carrying rate as evaluation indexes, the FDA with the best performance was selected and the concentration was optimized. In addition, the experimental results were verified by surface tension measurement and electron microscopy observation. The results showed that the sulfonate compound surfactant (UT-6) had good foamability, excellent foam stability, and better oil resistance at high temperature and high pressure. In addition, UT-6 had stronger liquid carrying capacity at a lower concentration, which could meet the production requirement when the salinity was 80 000 mg/L. Therefore, compared with the other five FDAs, UT-6 was more suitable for HTHP gas wells in block X of the Bohai Bay Basin, whose optimal concentration was 0.25 wt %. Interestingly, the UT-6 solution had the lowest surface tension at the same concentration, with the generated bubbles being closely arranged and uniform in size. Moreover, in the UT-6 foam system, the drainage speed at the plateau boundary was relatively slower with the smallest bubble. It is expected that UT-6 will become a promising candidate for foam drainage gas recovery technology in HTHP gas wells.

Tight oil reservoirs require fracturing techniques to create complex fracture networks for efficient development. It is frequently accompanied by a dynamic matrix-fracture imbibition process, promoting enhanced recovery. At present, the mechanism of three dimensions (3D) matrix-fracture dynamic imbibition at the pore scale has not been fully elucidated. In this paper, the dynamic imbibition process of oil-water two phases in matrix-fracture was simulated based on the Navier–Stokes equations, and the level set method was used to capture the real-time interfacial changes between the two phases. It was found that during matrix-fracture dynamic imbibition process, oil-phase droplets in a single pore remain in the pore mainly due to the “stuck” effect. Cluster residual oil in the pore space is mainly retained due to the “flow around” effect. Continuous residual oil in the deeper regions of the matrix is due to insufficient capillary force. Water phase in the micro-confinement space of a tight reservoir intrudes into the pore space along the pore corners, forming the “fingering” phenomenon is beneficial for enhancing the efficiency of micro-dynamic imbibition. It differs from cognition obtained in the micro-view space during conventional water flooding. The enhancement of imbibition efficiency is often accompanied by the occurrence of fluctuations in the average pressure within the matrix. Therefore, a method involving impulse type of high-frequency and short-period for supplemental energy and imbibition is suggested to enhance recovery in tight sandstone reservoirs. This study reveals the detailed mechanisms of oil-water two-phase transport at different stages in the dynamic imbibition process and holds significant guiding implications for enhancing recovery in this type of reservoirs.

CO₂ pre-injection fracturing is a promising technology for shale reservoirs development, with multiple advantages for improving the complexity of fractures, the production of crude oil, and the sequestration of CO₂. Previous research mostly focused on the CO₂ effect on macroscopic mechanical properties of shale. However, there are many phenomena closely related to shale micro mechanical behavior. Therefore, this study presents a systematic investigation into the effects of CO₂ on both macro and micro mechanical properties, as well as pore-fracture structures during CO₂ pre-injection fracturing in shale reservoirs. The results show that CO₂ can significantly decrease the tensile strength, uniaxial compressive strength, and elastic modulus of shale. With the increasing CO₂ treatment time, the macro mechanical properties of shale decrease gradually. The microscopic experiments show that this significant decrease may be due to two mechanisms. The first is the significant decrease in the micro-mechanical properties of shale. The results of indentation analysis show that the microscopic elastic modulus and hardness of shale decrease by 51.3% and 63.3% after CO₂ treatment. The second is the changes of the original shale framework. Pore-fractures structure analysis showed that after CO₂ treatment, a large number of dissolution pores are generated in the shale matrix. Meanwhile, there are propagation of original fractures and opening of structural weak planes, which lead to the form of new fractures. Under the action of these two mechanisms, the macro mechanical strength of shale is reduced significantly. Therefore, in the field application, proper soaking following CO₂ injection could lead to a significant overall reduction in mechanical strength, potentially lowering formation breakdown pressure, easing the requirements for treatment equipment, and enhancing fracturing effects.