The primary benefit of metamaterials is that their physical and mechanical properties can be controlled by changing the structure geometry. Numerical analysis tools used in this work offer a few advantages over full-scale testing, consisting of an automated process, as well as lower material and time costs. The investigation is concerned with the behavior of unit cells of the tetrachiral mechanical metamaterial under uniaxial compression. The base material is studied within an elastic mathematical model. The influence of topological defects of the unit cell on the metamaterial properties is studied for the first time. Defects, and especially topological defects, play a decisive role in the mechanical behavior of materials and structures. The unit cell without defects reveals orthotropy of properties. Torsion of a cell with a chiral structure is induced by the rotation of all tetrachiral walls, and therefore it is sensitive to the introduction of defects. There are cases of increased torsion as well as of no compression–torsion coupling effect. In the latter case, the unit cell experiences only shear. The effective Young’s modulus is calculated to vary in the range from 23 to 57 MPa for unit cells of different topologies. With the successive introduction of defects in two walls, the studied characteristics increase, correlating with each other. A further increase in the number of defects affects the characteristics in different ways. The introduction of two more defects in the walls decreases torsion and increases Young’s modulus, after which both characteristics decrease. The introduction of topological defects in all walls of the unit cell leads to the orthotropic behavior of the cell with the opposite sign of torsion.
This paper studies a mechanical metamaterial with tetrachiral topology by mathematical modeling. Chirality is the property of an object that makes the object distinguishable from its mirror image; chirality can be left- or right-handed. The mechanical response of two metamaterial unit cells with different configurations (patterns A and B) is investigated. It is found that the cubic cell with a regular pattern A exhibits orthotropic mechanical behavior under loading along three coordinate axes. An irregular pattern B differs from pattern A in that the upper face of the unit cell has an opposite chirality. This architectural transformation is considered as a topological defect, which enhances the twisting effect in the loaded metamaterial. Analysis of displacements and stresses shows that the mechanical behavior of the pattern B cell is described by the model of a transversely isotropic material. The orthotropic and transversely isotropic behavior of the cells of given configurations is also confirmed by the values of the effective elastic constants. Microstructural geometry and mechanical deformation of metamaterials are shown to be closely related. It is shown that a topological defect in a unit cell of a tetrachiral metamaterial strongly determines its twisting behavior.
1 June 2022 in Vestnik Tomskogo Gosudarstvennogo Universiteta. Matematika i Mekhanika
The main focus in the development of metamaterials is on the design of multiscale structures, rather than on the chemical composition and properties of the base materials. In this work, a mechanical metamaterial is studied by mathematical modeling and computer simulations. A tetrachiral metamaterial structure is chosen due to its specific rotational behavior under uniaxial loading. Special attention is paid to the efficient use of the base material in the design of metamaterial samples. Two types of connection between unit cells in a macrobody are discussed: adjoining and overlapping. It is shown that a much less amount of the base material is used in 1D, 2D, and 3D samples consisting of overlapping cells. Numerical calculations of uniaxial loading of a system of two adjoining and overlapping cells showed that the adjoining cells act on each other, their contacting walls rotate in opposite directions due to chiral structure, and the sample is twisted. The overlapping cells have one common wall that rotates in one direction only, leading to a more pronounced twisting of the sample.
Powder compacting is a widely used process for both metallurgy and pharmaceutical production. The mathematical simulation of the powder compaction process is a promising tool for its study. The compacting of WC/Co powder by a punch in a cylindrical die is simulated in this work. The use of the Drucker-Prager Cap constitutive model is made. Results on stress distribution and volume plastic deformation during compaction are obtained. Relative density distribution in the powder compact can also be estimated from volume plastic strain. The severe influence of frictional contact between powder and die wall on the results is noted.