This paper describes the development of ZnO semiconductors applied as photocatalysts for the degradation of water contaminants, with the shape of ceramic pellets thick enough to maintain their structures, prepared by slip casting and sintering. The samples presented porosities around 40% and densities around 3.4 g/cm3, which represented about 61% of the theoretical density of ZnO. After obtaining the ceramic samples, the degradation of Rhodamine B dye by photocatalysis was evaluated in six cycles of degradation. After the cycles, changes in the surface of the samples were verified, possibly due to leaching during photocatalysis since they presented mean grain sizes of 0.61 μm before and 0.36 μm after the photocatalysis. The ceramic ZnO samples were able to satisfactorily degrade Rhodamine B for several cycles, resulting in successful reuse of photocatalysts and increased facility of removing the photocatalysts from the medium after degradation compared to powders in suspensions.
Photocatalysis is a promising alternative for the decontamination of effluents. In this paper, immobilized ZnO-based photocatalysts were obtained by pressing and by slip casting. The cylindrical pieces were heat treated at 800°C. The samples were characterized by the method based on the principle of Archimedes, XRD, FTIR, Raman, diffuse reflectance and SEM. The samples obtained by slip casting presented lower apparent density (3.12 ± 0.04 g/cm3), higher apparent porosity (44.87 ± 0.47%) and smaller grain size (0.48 ± 0.05 µm) when compared to the pressed samples, with mean apparent density of 5.37 ± 0.08 g/cm3, apparent porosity of 1.56 ± 0.10% and grain size of 0.64 ± 0.02 µm. The performances of the samples were attested by the photocatalytic degradation of Rhodamine B (RhB) under UV-C irradiation (maximum intensity at 254 nm). The samples obtained by slip casting showed photocatalytic degradation between 80 and 90%, while the pressed samples showed degradation between 40 and 60%. The reuse of the photocatalysts was evaluated over five cycles of photocatalytic degradation, in which there was no loss of performance of the samples obtained by slip casting; however, the pressed samples showed a loss of photocatalytic efficiency starting from the third cycle. Photocatalytic assays were carried out with different dye concentrations, in which the slip casting samples showed better photocatalytic efficiency (degradation of 80% for a RhB concentration of 10 mg/L) due to higher porosity and surface area compared to pressed samples, and there was a loss of performance in higher concentrations.
This paper puts forward the use of “low-cost/low-end” hydroxyapatite-based adsorbing materials prepared from Tambaqui fish cleaning residues (i.e., bones) by grinding and/or thermal annealing. The nature of raw materials and treatments practically resulted in a “zero-cost” adsorbent for atrazine pesticide and Co2+ ion remediation in an aqueous solution. Despite the distinctive character of the two contaminants, all adsorptions were found to follow pseudo-second order kinetics and Freundlich isotherm models. Pristine hydroxyapatite proved to be more effective in adsorbing atrazine at low concentrations due to interactions with collagen residues. Conversely, heat-treated materials demonstrated better adsorption performances for cobalt due to the removal of organic residues hindering access to the surface. On the other hand, lower adsorption affinities resulted into a faster and more efficient Co2+ release into water. The different behavior in terms of phosphate and cobalt release shown by the three hydroxyapatite-based absorbents can be exploited for differential liberation of targeted nutrients, with high seed germination rates. Considering circular economic principles, waste-derived hydroxyapatites may be potentially attractive for removing ionic species, minimizing water pollution stemming from heavy industry, and for their subsequent targeted release to edible plants, enhancing agricultural availability of mineral nutrients for soil fertilization.
4 October 2024 in International Journal of Applied Ceramic Technology