Ezgi Ceren Boz Noyan

Mrs. Ezgi Ceren Boz Noyan

Industrial and Materials Science, Chalmers University of Technology, Gothenburg, Västra Götaland, Sweden
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2016 in Thermochimica Acta
Verified
Journal Article
Closed access
Nihal SarierNihal Sarier
Nihal Sarier
RARefik Arat
Refik Arat
YMYusuf Menceloglu
Yusuf Menceloglu
Emel OnderEmel Onder
Emel Onder
ENEzgi Ceren Boz Noyan
Ezgi Ceren Boz Noyan
OOOguzhan Oguz
Oguzhan Oguz

1 April 2018 in Thermochimica Acta
Verified
Journal Article
Closed access
ENEzgi Ceren Boz Noyan
Ezgi Ceren Boz Noyan
Emel OnderEmel Onder
Emel Onder
Nihal SarierNihal Sarier
Nihal Sarier
RARefik Arat
Refik Arat

1 December 2022 in ACS Omega
Verified
Journal Article
Open access
ENEzgi Ceren Boz Noyan
Ezgi Ceren Boz Noyan
AVAbhijit Venkatesh
Abhijit Venkatesh
ABAntal Boldizar
Antal Boldizar
The functional properties of recycled post-consumer flexible polyethylene packaging waste have been studied using materials collected and sorted at a large-scale facility in Sweden. The studied fraction was used both as received and after simple laboratory washing in water with added sodium hydroxide at 40 °C. The materials were melt-compounded with a twin-screw extruder using two different temperature profiles and two screw configurations and injection-molded into slabs, whose thermal and mechanical properties were assessed. The results showed that the mechanical properties of injection-molded samples were not changed significantly either by the washing or by the temperature or screw configuration used in the compounding. Washing reduced the viscosity and molecular mass to a minor extent. As expected, the ash content of the compounded pellets was reduced by washing. The thermo-oxidative stability decreased with increasing compounding temperature and with washing.

1 November 2020 in Polymer Degradation and Stability
Verified
Journal Article
Open access
LFLilian Forsgren
Lilian Forsgren
ENEzgi Ceren Boz Noyan
Ezgi Ceren Boz Noyan
AVAlberto Vega
Alberto Vega
NYNazdaneh Yarahmadi
Nazdaneh Yarahmadi
ABAntal Boldizar
Antal Boldizar

14 December 2022 in Recycling
Verified
Journal Article
Open access
PDF file
ENEzgi Ceren Boz Noyan
Ezgi Ceren Boz Noyan
AVAbhijit Venkatesh
Abhijit Venkatesh
ABAntal Boldizar
Antal Boldizar
The mechanical and thermal properties of injection-molded recycled polyethylene were studied, specifically with respect to the influence of large-scale washing and melt-compounding of polyethylene from post-consumer packaging waste. Three types of materials were studied: those taken after sorting, after sorting and washing, and after sorting, washing, and melt-compounding, including melt-filtration, all from a large-scale material flow. The materials were further processed on a laboratory scale and compared. The results showed that large-scale washing significantly reduced thermo-oxidative stability, as well as molar mass and melt viscosity. The degradation during large-scale washing made the material susceptible to further degradation in the subsequent extrusion compounding, as shown by the differences in compounding at 240 and 200 °C using a high-shear screw configuration. The compounding parameters, screw configuration, and compounding temperature did not influence the stiffness and strength of the unwashed and large-scale-washed materials, but the elongation-at-break varied, specifically, with the increased temperature. Washing had an influence on the mechanical properties as well, and the unwashed material provided molded samples with stiffness measurements of approximately 550 MPa, whereas the large-scale-washed material provided stiffness of approximately 400 MPa. The strength measurements were approximately 15 MPa for samples made of both unwashed and large-scale-washed material, and the elongation-at-break measurements were between 50 and 150%. The large-scale-washed and compounded materials had very different mechanical properties, with stiffness measurements of approximately 320 MPa, strength of approximately 20 MPA, and elongation-at-break of approximately 350%. The significantly different mechanical properties of the large-scale-washed and compounded materials were likely due to the melt-filtration included in the compounding through the removal of metal and rubber particles, and they may also have been due to the compatibilizing and stabilizing additive used in the compounding.

17 April 2024 in Materials
Verified
Journal Article
Open access
PDF file
ENEzgi Ceren Boz Noyan
Ezgi Ceren Boz Noyan
FRFranziska Rehle
Franziska Rehle
ABAntal Boldizar
Antal Boldizar
The properties of recycled post-consumer rigid polyethylene packaging waste were studied, using sorted waste washed in the laboratory with water alone and with added detergent, and compared with large-scale high-intensity washed flakes. The washed flakes were compounded using three different temperature profiles in a twin-screw extruder and then injection molded. A higher compounding temperature reduced the thermo-oxidative stability, the average molecular mass, and the viscosity of the samples. Rheological measurements suggested that changes in chain branching occurred at different compounding temperatures. The strength and the elongation at break were also influenced by the compounding temperature in both the molten and solid states. Detergent washing maintained the thermo-oxidative stability in contrast to washing with water. The large-scale washed samples had a relatively high thermo-oxidative stability, a higher melt elasticity, and a lower elongation at break in both the molten and solid states than the laboratory-scale washed samples. The thermal properties, melt elasticity, Young’s modulus, yield stress, and yield strain of the samples were not, however, significantly affected by either the compounding temperature or the washing medium and intensity. The results indicated that recycled post-consumer rigid polyethylene packaging waste has properties that can support further applications in new products.