Starch foams were prepared from four types of potato starch using two-step extrusion with an intermediate conditioning step at 53% relative humidity in order to control the moisture content. The moisture content was the driving force for the expansion during the second extrusion. The second extrusion was performed with two different dies in order to achieve differences in porosity of the materials. Glycerol in combination with water was used as plasticizer for the starches. The rheological properties of the melts and the moisture content of the starch materials prior to the expansion were determined. The porosity of the expanded structures was characterized using environmental scanning electron microscopy imaging and density measurements. The absorption capability of the starch-based foams was investigated using aqueous NaCl solutions, and the water uptake of thin starch-based films from humid air was also evaluated. Foams prepared from amylopectin potato starch were found to exhibit the highest porosity, the lowest density, and the greatest absorption capability, both from water and from humid air. Not only the density but also the absorption capability was influenced by the porosity level.
Hydroxyazetidinium salts were used to surface-modify cellulose nanocrystals (CNC) by grafting the salts onto the sulphate ester groups on the CNC surfaces. The grafting was confirmed by ζ-potential measurements and by the thermal degradation behaviour of the modified CNC. The thermal stability (onset of degradation) of the CNC was improved by the surface modification (almost 100 °C). Composites containing surface-modified or unmodified CNC (0.1, 1.0 and 10 wt%) with an ethylene-based copolymer as matrix were produced by compression moulding. The thermal stability of the composites was not, however, markedly improved by the surface grafting onto the CNC. It is suggested that this is due to a degrafting mechanism, associated with the alkaline character of the system, taking place at high temperatures. Model experiments indicated, however, that this did not occur at the conditions under which the composites were produced. Furthermore, in the case of a reference based on pH-neutralised polymeric system and modified CNC, an upward shift in the onset of thermal degradation of the composite was observed. The addition of the CNC to the polymer matrix had a strong influence of the mechanical performance. For example, the tensile modulus increased approximately three times for some systems when adding 10 wt% CNC. The surface grafting of the hydroxyazetidinium salts appeared mainly to affect, in a positive sense, the yield behaviour and ductility of the composites. The results of the mechanical testing are discussed in terms of interactions between the grafted units and the matrix material and between the grafted groups.
Waste electrical and electronic equipment (WEEE) is growing rapidly, and the plastics within WEEE have an important role in fulfilling the recovery and recycling targets defined in the European WEEE Directive. This study considers recycling of WEEE plastics by making a blend of the different plastics instead of separating them. The mechanical and thermal properties can be enhanced by adding a compatibilizer. It was found that one compatibilizer, a styrene-b(ethylene-co-butylene)-b-styrene (SEBS) copolymer named Kraton® G1652 E, had a large impact on the ductility of the recycled WEEE plastics blend. By adding 2.5 weight % (wt%) of this copolymer, the elongation at break increased by more than five times compared with the non-compatibilized samples, with only a small decrease in stiffness and strength. The storage modulus (G’) decreased slightly with increasing compatibilizer amounts while the impact strength increased with increasing amounts of compatibilizer, from 2.1 kJ/m2 (reference material) to 3.6 kJ/m2 (5 weight % (wt%) compatibilizer). It was found that Kraton® FG1901 E (styrene-b(ethylene-co-butylene)-b-styrene (SEBS) grafted with maleic anhydride (MAH)), Royaltuf® 372P20 (styrene acrylonitrile (SAN) modified with ethylene-propylene-diene elastomers (EPDM)) and Fusabond® P353 (polypropylene (PP) with a high degree of grafted MAH) were ineffective as compatibilizers to the blend. Gamma irradiation (50 kGy) did not improve the mechanical properties however: the impact strength of the gamma-irradiated samples was lower than that of the non-irradiated samples.