The term “smart materials” can be used to refer a wide variety of different kinds of substances. One capacity that is shared by all of them is the capability to radically alter one or more aspects while operating inside carefully controlled conditions. The age of intelligent materials is arrived, and we are living in it right now. An older definition of smart material described it as a substance that responds swiftly to the environment in which it is located. It has been argued that the word “smart material” now refers to any substance that is capable of detecting, transmitting, or processing a stimulus in order to produce a beneficial effect. This idea has been put forward as a possible expansion of the original meaning of the term. The purpose of this research is to define and categorize different types of intelligent materials. Uses of smart materials are being contemplated in a wide variety of domains, spanning from the realm of technology to that of the modern environment.
This study presents an extensive survey of the many surface treatments that may be given to natural fibers for use in advanced composites. When put into reality, the primary disadvantages of working through biological fibers are the increased level of moisture intake that natural fibers possess as well as their low dimensional stability. The fundamental purpose of applying surface treatments to natural fibers is to optimize the bonding strength as well as the pressure transferability in composites made of biological natural fibers. Natural fiber-strengthened polymer composites (NFPC) have overall mechanical qualities that are strongly dependent on the morphological, aspect ratio, hydrophilic propensity, and high stiffness of the natural fibers that are employed in the composite. Cellulosic fibers are being studied for their effects both before and after being used as reinforcements for thermoset and thermoplastic polymers. Some of the chemicals utilized in treatments include alkalis, silane, acetyl, benzoylation, acrylation and polyamide grafting, maleated linking agents, ammonium nitrate, peroxide, phenoxy, stearic acid, potassium chalcopyrite, triazine, synthetic derivatives of fatty acids (oleoyl chloride), and fungi. After chemical treatment, composites made from organic fibers are stronger and more dimensionally stable than the untreated sample.
28 January 2022 in Advances in Materials Science and Engineering
Composite fiber reinforcement is one such proficient material that substitutes for useful applications for conventional and polyester blends where little weight and thus less energy conservation is required. This study highlighted the importance of recently discovered Agave Angustifolia marginated (AAM) fibers extracted by a manual process from AAM plants. This paper observes the various properties of the mechanical and moisture intake characteristics of AAM fiber and compares these to other naturally occurring fibers. Using isophthalic polyester resin, the mixed chopped AAM fiber-reinforced composite is prepared and detailed preparation techniques are presented. During physical composite testing, fiber pull-outs on the broken samples were investigated. Additionally, the experimental evidence demonstrates that increasing the volume fraction helps to increase the tensile, bending, and modulus of the AAM fiber composite. The chopped fiber isophthalic polyester reinforcement reaches its improved tensile strength and modulus at a 25% Vf about the 20 mm length of the fiber.
1 January 2021 in Advances in Materials Science and Engineering
The nickel‐based Colmonoy‐5 hardfacing alloy is used to hard‐face 316LN austenitic stainless steel components in fast reactors. The nominal composition (in wt%) was listed as follows: 0.01 C, 0.49 Si, 0.87 Mn, 17.09 Cr, 14.04 Ni, 2.56 Mo, 0.14 N, and balance Fe. Hardfacing is a technique of applying hard and wear‐resistant materials to substrates that need abrasion resistance. The thickness of hardfacing deposit varies between 0.8 mm and 2 mm based on parameter combinations. In this study, laser hardfacing process parameters including laser power, powder feed rate, travel speed, and defocusing distance were optimized to reduce weight loss of laser hard‐faced Ni‐based deposit. The tribological characteristics of reactor‐grade NiCr‐B hard‐faced deposits were investigated. The RSM technique was used to identify the most important control variables resulting in the least weight loss of the nickel‐based alloy placed on AISI 316LN austenitic stainless steel. Statistical techniques like DoE and ANOVA are utilized. Changing the laser settings may efficiently track the weight loss of laser hard‐faced nickel alloy surfaces. These are created using the response surface technique. The deposit produced with a laser power of 1314 W, powder feed rate of 9 g/min, travel speed of 366 mm/min, and defocusing distance of 32 mm had the lowest weight loss of 16.4 mg. Based on the F value, the powder feed rate is the major influencing factor to predict the hardness followed by power, travel speed, and defocusing distance.
16 November 2023 in Advances in Materials Science and Engineering
Cement-based materials are increasingly and widely employed in infrastructure development; however, they pollute our environment by generating carbon dioxide, which is detrimental to our civilization. In self-cleaning concrete, photocatalysts accelerate the decomposition of organic particles; thus, photocatalytic degradation of gaseous pollutants could reduce pollution. The incorporation of photocatalytic components enhanced the mechanical self-cleaning properties of cement mortar. In this study, 46 percent by weight of rutile TiO2 was added to mortar, and the results were compared to those of a control sample. On the proposed mortar cubes, both fresh mortar and hardening mortar experiments were conducted. Because the initial and final setting times of TiO2 differ from those of conventional cement mortar, the surplus TiO2water-cement ratio had to be modified. The adaptability of the sol-gel method enables the use of various process parameters to influence the properties of the produced TiO2 nanoparticles. The compressive strength was calculated for 7, 14, 21, and 28days, and an ultrasonic velocity test was performed after 28days. On mortar samples, acid and sulfate attack experiments were performed. The M-3 mortar mixture containing 5 rutile exhibited the highest level of strength compared to the other mixtures. The M-3 exhibits a strength that is 10.96 greater than that of the control mix. The impact of acid and sulfate attack on the strength of mix M-2 is relatively modest in comparison to other mixtures. Using RhB (rhodamine color) discoloration under UV light, such as sunlight, the photocatalytic mortar is concentrated; a typical test for self-cleaning cementitious materials reveals the presence of more photocatalytic material, which yields the best results.