Genaro Rico-Baeza

Prof. Genaro Rico-Baeza


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 November 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
GRGenaro Rico-Baeza
Genaro Rico-Baeza
Gerardo I. Perez-SotoGerardo I. Perez-Soto
Gerardo I. Perez-Soto
LMLuis A. Morales-Hernández
Luis A. Morales-Hernández
Enrique Cuan-UrquizoEnrique Cuan-Urquizo
Enrique Cuan-Urquizo
Karla A. Camarillo-GomezKarla A. Camarillo-Gomez
Karla A. Camarillo-Gomez
This study presents the development of insoles using 3D scanning and additive manufacturing; additionally, the feasibility of implementing cellular structures in their design was evaluated. Using finite element models, the displacements and Von Mises stresses in the insoles were obtained considering the exerted pressures of a person during walking. The insoles developed in this work presented a decrease of 91.48% in deformation while the maximum Von Mises stress increased by 32.62%, compared with what other authors reported. The Von Mises stresses and displacements in the insole were calculated when two cellular topologies, triply periodic minimal surfaces (TPMS) and body-centered cubic (BCC), and different relative densities (10.33%, 14.67%, and 20.19%) were implemented. When compared to solid insoles, the Von Mises stresses and displacements for the models with cellular structures increased. The maximum Von Mises stresses and displacements resulted for the insoles with a relative density of 10.33%; for the insole with the BCC cellular structure, the displacement was 2.06 mm, and the Von Mises stress was 22.17 MPa, while for the TPMS structure, these were 2.7 mm and 23.84 MPa, respectively. The designs were additively manufactured, and the printing defects were visually characterized.

9 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
GRGenaro Rico-Baeza
Genaro Rico-Baeza
Enrique Cuan-UrquizoEnrique Cuan-Urquizo
Enrique Cuan-Urquizo
Gerardo I. Perez-SotoGerardo I. Perez-Soto
Gerardo I. Perez-Soto
Luis Alejandro Alcaraz-CaracheoLuis Alejandro Alcaraz-Caracheo
Luis Alejandro Alcaraz-Caracheo
Karla A. Camarillo-GomezKarla A. Camarillo-Gomez
Karla A. Camarillo-Gomez
Natural porous materials adjust their resulting mechanical properties by the optimal use of matter and space. When these are produced synthetically, they are known as mechanical metamaterials. This paper adds degrees of tailoring of mechanical properties by producing double levels of gradation in lattice structures via cross-section variation in struts in uniformly periodic lattice structures (UPLS) and layered lattice structures (LLS). These were then additively manufactured via material extrusion (ME) and vat photopolymerization (VP). Their effective mechanical properties under compressive loads were characterized, and their stiffness contrasted with finite element models (FEM). According to the simulation and experimental results, a better correlation was obtained in the structures manufactured via VP than by ME, denoting that printing defects affect the correlation results. The brittle natural behavior of the resin caused a lack of a plateau region in the stress–strain curves for the UPLS structures, as opposed to those fabricated with ME. The LLS increased energy absorption up to 244% and increased the plateau stress up to 100% compared to the UPLS. The results presented in this paper demonstrate that the mechanical properties of lattice structures with the same base topology could be modified by incorporating variations in the strut diameter and then arranging these differently.